K2TLEFFWMS00 KitchenAid Refrigerator - Instructions

I followed the instructions in the video on the PartSelect website. The only problem I ran into was that I couldn't switch the grounding tab connector from the original side of the motor to the other. I had to add more wire so that I could reach it in its new location.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .

1. I removed the plastic back cover panel in the freezer. 2. Took flash photos with my phone of the motor and wire configuration. 3. Removed noisy Evaporator fan bracket from freezer. 4. Removed Fan Blade from old Motor. 5. Removed old Motor from Bracket. 6. Installed New Motor into the bracket. 7. Installed the fan blade onto motor spindle. 8. Installed the bracket onto the back wall of freezer. 9. Noticed that the tab for the ground wire was inaccessible. 10. Cursed like Linda Blair in the Exorcist for about 5 minutes. 11. Repeated steps 3 - 5... 12. Unscrewed the ground tab and placed it on the opposite side and screwed it back in. 13. Repeated steps 6 & 7.... 14. Tried to install the bracket and motor back onto the freezer but the bracket screw holes weren't lining up. When I removed the motor to flip the ground tab over, I reinstalled the motor onto the bracket upside down. 15. Tear some hair out of my head. 16. Repeated steps 4 & 5 and flipped bracket over. 17. Repeated steps 6 - 8... 18. Placed wires onto tabs. 19. Ground wire would not stay securely onto the tab. 20. Slightly opened up metal fastener of ground wire with needle nose pliers and stuck it onto the tab. 21. Still not on there super tight. I gave up wrestling with it and just prayed it will stay on there anyway. 23. Turned on freezer to check if it works. 24. Reinstalled plastic back plate. 25. Put melted food back into freezer.

Nothing to do, just unrap shelf from delivered package, wipe clean and put in refridgerator.

Instructions were really clear and easy to follow. Hardest part of the job was moving the refrigerator away from wall after it was filled with holiday groceries.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

Took out old and replaced with new shelf piece.

Removed the drawer. removed the frame washed the glass that was fine. put the frame in place put the glass on top slid drawer in place. and I was done.

Was very easy to identify part on the website, ordered with standard shipping and was delivered the second business day. Could not have been easier. Good pricing too.

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

I watched the film on installing and taking out. Step by step. easy.

I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

The repair was very easy, unplug ref. open freezer door, and remove base plate, then remove screws on back plate. I had to tilt top of back plate to remove from freezer. This gives you access to the evap. fan Pull of the three wires, and remove screws from fan bracket, which bolts to the back of ref. Remove fan motor from bracket (2) screws, remove motor, and put replacement motor on bracket, pull fan blade off old unit and push on new motor shaft. Reverse the installation, and you are done. Pretty easy.