JW2000A Jenn-Air Washer - Instructions

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.

removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!

UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel that you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done

It was easy to replace the water pump

Repair was very easy. I removed the old pulley from the motor shaft by breaking it. And then tapped the new one into place. It works great. DON'T buy a new motor for $120, just replace the pulley $6. This whirlpool pulley fits the Admiral motor perfectly!

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

replaced pulley and belt. Looked for a pulley for 1 week at retail stores. Found pulley on parts select

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.

My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.

The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I finally decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]

Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas

Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .