JTP85BA4BB General Electric Microwave Oven Combo - Instructions

Removed back panel, change out sensor

Removed element. Ordered new one. Installed it.

Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on

Removed old element with a socket wrench. Replaced new element with socket wrench. Pretty easy!

Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch).
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

This is a pretty easy job. Took 20 min. because I was especially careful. Once the new element arrived, I simple shot off the power (DO THAT, BE SURE TO DO THAT ). Two 5/16 screws hold the element in place at the rear of the oven. Once removed the element can move forward. A surprise was that wires attached to the element come with it. There are simple push on connections on the element. There were a little difficult to remove (heat I am sure ), but a couple of needle nose plyers and the two wires removed with ease. Plug in the new element connectors and push the wires and the connection back into place. Once in place, reinstall the screws and test.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

Used a nut driver to remove element the insulation was tight and pulled the wires off before they came out of the oven. I made a small hook out of a coat hanger and pulled the wires through the opening.

Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.

Disconnected power, removed two screws from bracket. Unplugged old element, installed new element and replaced screws in bracket. Restored power and back in business!

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

Simple job. Disconnected the power to the oven, removed the two screws holding the old lower element, pulled it out and disconnected the two electrical wires. Installed the new one by simply reversing the removal process. Very impressed with PartSelect on price and delivery. My local repair company wanted to charge me twice the price and a part delivery time three times longer. Will definitely use PS in future

basically unscrew two screws, unplug, plug new one in and screw the screws back in.

Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.