JTP48BFB General Electric Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bake element was broken and needed to be replaced
The repair was very simple. In fact the biggest challenge was finding the correct socket set.
Parts Used:
-
Darthy from Dacula, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
broken switch
This was a wall mounted oven. Turned off breaker. Pulled panel off by removing 6 screws. Pulled connectors off old switch. Removed old switch. Just a friction fit. I used my jack knife to get it moving. Pushed in the new switch and connected wires. (just push on tabs) Put panel back together and turned on breaker. Done, easy.
Parts Used:
-
Bob from Marcy, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven heating element was burnt through.
Identified part with Part Select, placed order. Opened the power breaker for the oven. Removed oven door (slides off) to improve access, removed burnt element (2 screw and 2 electrical blade terminals). Installed the new element and tested. Reattached oven door.
Parts Used:
-
george from Moorpark, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Broil element on top oven was not working
Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".
Parts Used:
-
andrew from pittstown, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Broiler Element burnt out
The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element. They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?
Parts Used:
-
Cherri from Katy, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
gasket replacement
Took about 15 minutes to take the old one off and put the new one on. Not difficult at all.
Parts Used:
-
Marilyn from Auburn, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Parts Used:
-
Anne Marie from Andover, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Door Switch
I unplugged the defective plug and replaced it with the new one. Took 5 min total
Parts Used:
-
Peter from Green Valley, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Heating element was fried.
Remove 2 nuts attaching element to oven. Pull element out 1" to 2" exposing electrical leads. Pull leads off old element. Replace with new. Toughest part is seeing the elements in a dark oven. Have a light handy.
Parts Used:
-
Roger from Cranberry Twp, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Heating Element
Removed two screws, removed two wires, installed new element. So easy a caveman could do it.
Parts Used:
-
Bradley from Perryville, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
no racks to oven
-
Johnette from Baltimore, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lower heat element burned out
Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.
Parts Used:
-
michael from marstons mills, MA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Missing oven rack
-
Damaris from Easton, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broiler heating element was not working
Turned off the circuit breaker. Removed 5 screws. Unplugged the heating element and then plugged in the new one and replaced the 5 screws. Very simple.
Parts Used:
-
Jim from Hyrum, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!