JS48PPDUDE01 Jenn-Air Refrigerator - Instructions

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Just needed to replace the water filter

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Easily removed old filter and inserted the new one

My icemaker quit 3 years back and at that time I searched for do-it yourself repair books with no success. I found this parts place web site and people having the same problems as myself. I purchased the parts as others have and problem solved! Ice all the time, woo hoo!

I went online and watched a U-tube video that said it was most likely the electronic emitter and receiver boards and showed how to replace them. I first unplugged the appliance (just to be safe) then, I unscrewed the screws holding the faceplate on. The board simply has a plug which you unplug with a little care and effort. I then plugged in the new board, resituated it into the hole and screwed the faceplate back on. You simply do the same for the other board on the other side. Viola! Lots and lots of ice!! The guy at sears said I shouldn't do work on such a complex appliance. Probably because I am a woman! Anyone can do this job! Winning!

After unplugging refrigerator, removed emitter and receiver cover plates on each side of freezer unit (3 screws each) and mounting screws for circuit boards. Unplugged old boards and plugged in new ones and reinstalled boards and then cover plates. Although, indicator code lights seem to still indicate a problem, ice maker has resumed operating after 24 hr.

My ice maker about six months ago started to ice make very intermittently and eventually stopped all together. The emiitter no matter what I did was giving me two flashes then a pause, over and over again. I purchased the emitter kit and with a Phillips screwdriver in about five minutes my ice maker kicked the sulinoid on and ice was already started!!! Fast and easy repair!!!

I replaced the Electronic control boards because the indicator lights were letting me know that there was a problem, but!!!! when that did not fix the problem, I took the ice maker out and removed the control module from the end of the icemaker only to find out that water had gotten in there and corroded the electronic contacts... this may have been why the indicator lights were not working on the emitter and receiver. I was going to purchase just the module, but the entire ice tray was beginning to de-laminate and plastic was flaking off all over. To make a long story somewhat shorter, I purchased a new icemaker and it works fine... one caution though... My icemaker did not come with any information that told me I had to flip the icemaker to the "on" position from vacation mode by inserting a screwdriver in the back of the module inside of a small white ring. This hole is where the shut off arm WOULD go if my model had one.

Put One card in one side and other card on the opposite side, push in on both sides to press in clips that hold light in. Once clips are in light will start to come out unplug light and plug in new light. Push light back in.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Did not have elec. schematics or instructions, thought the problem may be the emitter/receiver. Ordered these parts, and included in the package were instructions for testing the e/m bd. Followed instructions for testing the e/m and determined the e/m was OK. Did not remove the boards from the box. Checked the internet and found schematic for the ice maker, tested and determined the ice maker was faulty. Problem solved.