JS48PPDUDE01 Jenn-Air Refrigerator - Instructions

Our unit is a built-in unit so first had to remove the decorative cover panel to expose the internal on/off switch. Turned off the circuit breaker. Disconnected the wires (simple pull-off/push-on). Removed the old switch which meant clipping the plastic tabs holding the switch in position. Inserted the new switch by simply pushing it through the opening being sure to have it in the same alignment ('off' to the back of the unit.) Reconnected the wires making sure to have a white ground wires on the left and the black 'hot' wires on the right. Turned the circuit breaker back on. Turned the switch on. Now it runs.

Light was blinking on the Electronic Control Boards. Ordered replacement (emitter and receiver)and installed, and now it's working.
Some note: 1 year ago, the board started to blinks (meaning it's bad) but it was still making ice. This gave me a false error when it really failed, took the risk and ordered the replacement parts and all is well now.

One more thing to pay attention to , and it may only be on my model of refrigerator, but the wires harness that connect to the receiver board (big board) have large and stiff wire. With limited space where the board and the wire are seat at, it put lots of pressure on the pressure on the board's connector. This pressure, over time, will cause the right angle connector's solders to crack and may be a contributor to the failure. If you're installing the new board, try to re-inforce the connector with some rubber heat glue and also relieve pressure from the connector's end, which I hope will prolong your board.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Repairing a refrigerator is inimidating to say the least. Our ice maker has broke twice in the two years that we have owned it. The first time we had a service repair faciliting come out and they replaced it for about $200. The second time I had no idea what the problem was until I came to this repair forum. I soon realized that the electronic control boards needed to be replaced. Received the part two days after ordering and it took all of about 5 minutes to unscrew the old boards, pop them out, and put in the new ones.

Love your website and the money that you saved me!!! Thanks a million!

power off, 3 phillips head screws on either side of freezer. unplg each board, plug new ones in completely. ( cannot mix them up, size difference) replace screws and enjoy ice cold beverages once again!!!!!!!!!

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

There is a good YouTube vid on how to extract the old LED without damaging the liner of the appliance. (Use a one inch plaster spatula and some blue painters tape). VERY IMPORTANT: The freezer LEDs and the one that was out in the fridge compartment are in series on the same circuit. I found out by trial and error after a frustrating start. If one or two are bad they all go out like a christmas light string. So be patient and keep replacing bulbs until they all come on. Then you can test each one you took out to see if it was bad or not by putting it back online. At first I was annoyed that Part Select may have sent the wrong replacement items but they were in fact correct. These bulbs are not cheap so make sure the ones you take out are truly burned out.

I think the lights are wired in series. When the light in the freezer goes bad several lights in the refrigerator go out but are still good. Replace the lamp in the freezer and all the lights in the refrigerator work again. The only tools I used was a 1" scraper and a very small flat screwdriver to pop the lamp assembly out. Not much room to work in so it was a bit of a job getting the wire connector where it needed to be but not to bad..

Being too lazy to pull out the refrigerator out and unplug it, I turned it off at the fuse box. Opened the freezer door and unscrewed the three screws holding the sensor. Pulled the sensor out and unscrewed the board then unpluged it and removed it. Plugged in new board, screwed it in then replaced the three screws. Repeat on the other side. The most difficult part was getting to one of three screws on each side; it almost required a third hand to hold the flap door between the ice maker and the bin, while removing said screw. I must at say that this product is definitely over engineered.

I removed the cap from the filter pushed a lever and removed fliter. I replaced the old filter, removed the caps on the new one and slid it into channel after replacing the outer cap. I removed water from the spigot for 4 mins. and it was ready to go. I pushed the reset button to get the green light to come on.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Just put the new one in.

I found an EXCELLENT video (see link below) that shows with great detail how to change out several parts in the water/ice dispenser area on the freezer door for KitchenAid or Whirlpool brand, side by side units. This made my repair so easy!

https://www.youtube.com/watch?v=yK8ZnbQQ8qU

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Built-in filter was corroded due to age. New filter corrected problem.