JNM1541LP2CS General Electric Microwave - Instructions

Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.

Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube

Removed control panel disconnected old capacitor installed new and returned the leads back on to the new. replaced control cover and tested

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

ordered 2 new sockets and bulbs easy replacement great service from this site

My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.

I first read the previously posted directions from other customers that were sent with my part order confirmation, which were all very helpful. Then, I basically used a screw driver to unscrew the screw holding the lens cover in place - be careful as it is a very tiny screw and it can easily fall behind your oven. You might want to place a large piece of cardboard over the space between oven and wall, as I did, so that you don't lose the screw in case it falls. Next I pried open the prongs, carefully slid out the cracked lens, and slid the new lens in place, pushed back the prongs and put the screw back in. I found that it was easier to use my fingers to first place and tighten the screw because it is very small and will keep falling out of place if you try to just use the screwdriver. Good luck!

.Thank You Dan

Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.

unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

Easy peasy - removed lens holder w/screw driver. Cleaned cover after removing damaged glass lens. Then unscrewed burnt out light bulbs. Installed new bulbs, slid in new light lens into holder and screwed back into bottom of microwave. Removed greasy filter and slid in new filter. Done!

Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward

llation

Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.