JMP26G*J1 General Electric Range - Instructions

The hardest part was removing the old nuthead screws off the old bake burner. Once those were off installing the new bake element was simple. One screw in each wire terminal, two hex head screws to hold the unit in place. Works like a charm!

Very easy, remove two screws, pull burner unit out slightly, then remove the two screws attaching the wires, one to each side, remove old unit and replace with new unit and replace screws.

Works fine perfect replacement.

Removed the racks, unscrewed the back plate which holds the element, unscrewed the leads from the element, removed the old part.

Reversed the process to install the new element.

Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.

And that was it; quite easy.

First I opened the shipping box that the new part came in and figured out which tools I would need. Then I went down to the cellar and clicked off the breaker that supplied power to the oven. In this case, it was the only 50 amp breaker in the panel so It was easy to figure out.
Then I hung a drop light inside the oven so I could see clearly and used a quarter inch drive ratchet with a quarter inch sized socket to remove the two self tapping screws that hold the element plate to the back of the oven. Then I used the same sized socket to remove the small screws that hold the wires and terminal ends to the element contacts.
Then I removed the old unit, placed the new one inside and reversed my steps till the new elements leads and bracket were both securely in place and the element supports were resting on the bottom of the oven. I then turned the power back on and set the oven for 350 degrees and switched the 'bake' selector on. Within thirty seconds, I had a nice even heating new element that glowed brightly from one end to the other. Success! Piece of cake. In the future, I plan to get all my appliance parts at PartsSelect.com and do a lot more repairs myself instead of just replacing the entire appliance.

Greg G. - Peabody, Massachusetts

I shut off the power at the breaker. Then I checked that the power was off by turning on the stove. Light did not come on, power is off. [ By the way, I locked the breaker box, in case somebody helpful came along to turn the power back on !] Then I undid the screws holding the old element . Pulled it out, and undid the screws holding the wire leads to the element. Screwed wire leads to new element. Pushed back in, and screwed brace screws back in. Went out to breaker box and turned power back on. Turned on oven. Worked. Second time I've done this. I kind of forgot how, since the last time was about 6 years ago, but anyone could figure this out, unless they didn't want to. Took 20 minutes. A little hard working in a small space , but beats buying a new stove.

1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.

total of 4 screws to remove and replace. Took out the first 2 and pulled element out a few inches. now remove the screws from the element itself but be sure you don't loose the wire out the back of the oven. The only challenge was to keep the wires from falling back through the rear of the oven. This could be easily avoided if you have a clamp of some type ie. clothes pin, hemostst, shop clamp ect.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Replaced baking lower element by disconnecting the mounting plate and wire connectors at the base of the element and then reinstalling new element by reconnecting the wire connectors and mounting plate. Key to this project: Know how to identify the cause of the problem as the crack in the baking element was not immediately visible until it was removed. One could easily have assumed that some other part of the range controls were defective.

Cut off power, but needed flashlight to see what I was doing. Couldn't get the flashlight to shine on right spot and had no one to hold it. Oven is 19 years old, so screws holding it into the oven wall and to the connection were very old and very difficult to loosen. Finally held prong with pliers and wrenched the screw loose after repeated tries and using a little WD40. Very proud of myself! I am a wife and mother of two teenage boys, but I end up doing all these projects. So proud that I posted a photo of the oven on facebook! Goes from 0 -350 in three minutes now. Yippee!

First, and most importantly, flipped the circuit breaker and turned off the power to the oven. Next, Unscrewed the old element and disconnected the wiring. Then, removed the old element and replaced it with the new one.
Reconnected the wiring to the new bake element and screwed it back onto the oven.

Voila! Turned the oven on and watched the new element heat to a bright red. We had an oven once again, and saved ourselves more than $100. Yay!

Ordered Bake Element - 240V from Partselect , when part received removed broken element with a screwdriver., replaced with new Bake Element with a screwdriver. Very easy to do.

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or so and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Removed the racks, removed two screws holding the element to the back of the oven, removed two screws holding wires to the element, installed by the reverse. BUT in my case the new element still didn't heat. The part was perfect so when the old element melted and shorted, it must have damaged the controlling switch (220V requires dual pole switch--apparently one side is now bad). Since the oven is over 30 yrs old, I'm returning the element and will buy a new oven.