JIM158XBCX1 Jenn-Air Ice Maker - Instructions

I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.

I thought the water bucket wasn't holding water because the icemaker continually was running - however, the crack didn't go through. The real issue was the Thermostat.

You've got to be able to sit or kneel and fit both arms in the unit for a while, so if you've got patience and ability, you can do it. If you have a battery operated screw driver with a nut and 6 star nut remover, this goes quicker.
Do not throw your old plug away, it doesn't come with a new one.

The hard part was getting the black thing (that attaches to the icebucket) back on. I had to go to Lowes and get a gasket and silicone grease to replace the one on it. I thought this was the reason it wouldn't go back on, because the gasket wouldn't fully fit back into the white hole.
I measured the diameter of that hole compared to the old one. It was slightly smaller and was not as smooth as my old one (it had manufacturing form lines and excess plastic that hadn't been removed)
I Dremeled it to increase the diameter, especially where the gasket was buckling out when trying to fit it on.
I finally got the black part back on.

I found later that it was cheaper somewhere else, however shipping charges are less and most parts are next day delivery.
I just ordered the thermostat. Wish me luck!

I took out old grid and removed the top broken wire. I attached the end of new wire to the terminal screw and carefully threaded the new wire back and forth without kinks. I was not able to get wire as tight as it was originally, but able to get it tight enough with pliers. I attached the other end to the opposite terminal screw. I had plenty of wire for the job and cut off the excess. I re-installed the grid and had ice the following morning. Feeling good about myself and saved a lot of money.

The real difficulty is removing the screws. Even with a nut driver the space available makes them difficult to remove. I went to the hardware store and replaced the screws with screwdriver slots for re-installation.

Found fault with recirculating pump. Found hot spot on pump circuit board . Replaced pump

Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

Simple to replace. Next fall I will be sure to drain the outdoor icemake and shut it down for the winter.

Received replacement valve ~ 3 days, easily replaced in less than 15min, works great

After turning off water to icemaker, defective control removed (two screws) and new unit installed.Worked perfectly.I was totally amazed when I ordered the part thursday afternoon and it arrived fridaY morning.Total time out of operation less than 24 hours.Wonderful results.

Easy. I took a picture with everything in tact. Took apart a couple of parts with screw driver. Replaced the pump. Put it all together and it worked fine.Thanks.

Removed lower vent cover and removed valve. Removed water lines and power hookups and attached to new unit. Approx. 15 Minutes total repair. Checked for leaks. Finished. Part select had replacement valve to my door within 24 hours. Great service and simple to understand installation instructions. Highly recommend.

I am the canteen manager at a V.F.W, our ice maker stopped working and I had an appliance technician come in and see what was wrong with it. The technician told me I needed a new compressor costing around $500.00. The next day I pulled out the ice machine and noticed there was condensation dripping on the start relay. I pulled the start relay from the compressor and saw a lot of corrosion. I then sealed the leek and cleaned the pins on the compressor. I ordered a new $40.00 start relay (which came in no time) and installed it. It works perfect.
Thanks Brian