All Installation Instructions for General Electric Range JGS968SH3SS

defective oven door seal

pull out defective seal with pliers clean area and press new seal into place making sure the spring clips on seal are completely inserted into door slots push ends of seal into holes in bottom of door

Parts Used:

Lower Oven Door Gasket

Brenda from Cave Creek, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Stove drawer rear guides broken

Installed new guides with a nut driver without any problems.

Parts Used:

REAR SUPPORT

Robert from Shakopee, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Range lower drawer would not stay on track.

Easy to install replacement parts using the screws provided.

Parts Used:

REAR SUPPORT

Richard from Newark, DE
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Parts Used:

REAR SUPPORT

Mario from Deer Park, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

missing meat thermistor

plug in thermistor when needed

Parts Used:

Meat Probe Thermistor

John R from Asheville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

f-2 or f-3

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Parts Used:

Temperature Sensor

daniel from gap, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

gasket replacement

Took about 15 minutes to take the old one off and put the new one on. Not difficult at all.

Parts Used:

Lower Oven Door Gasket

Marilyn from Auburn, WA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

broken switch

This was a wall mounted oven. Turned off breaker. Pulled panel off by removing 6 screws. Pulled connectors off old switch. Removed old switch. Just a friction fit. I used my jack knife to get it moving. Pushed in the new switch and connected wires. (just push on tabs) Put panel back together and turned on breaker. Done, easy.

Parts Used:

Door Light Switch

Bob from Marcy, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Ingiter would glow but gas would not come on

I had read the customers reviews and expected that I'd most likely break the attaching screws. My trick was to not just unscrew then all the way out but to turn it a half a turn and then screw it back in. Then out again a little more then last time and back a little. Didn't break a thing. I did have to move the stove out to get to the plug but that was just enough for me to get my arms in there.

Parts Used:

Oven Igniter

James from Coatesville, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Oven would not light due to igniter.

After reading reviews about corroded screws causing difficult removal I sprayed penetrating oil prior to installing replacement part. The oven doesn't need to be pulled out to fix. Just carefully pull wires through hole until the locking plug is visible & swap out. Very easy repair.

Parts Used:

Oven Igniter

Robert from Hillsboro, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Convection fan came loose from shaft

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Parts Used:

NUT

Thomas from Albuquerque, NM
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

F2 reading

Followed the instructions that were sent to me by E-Mail.

Parts Used:

Temperature Sensor

lynn from sunnyside, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Broken Door Switch

I unplugged the defective plug and replaced it with the new one. Took 5 min total

Parts Used:

Door Light Switch

Peter from Green Valley, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

oven not warming, f2 indicating overheat

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Parts Used:

Temperature Sensor