JGB3001ER4SS General Electric Range - Instructions

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.

repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter

Took longer to open the box.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.

Ordered the parts and put them on. No tools, no problems

replace sensor

Ordered new Surface Burner Knob- Stainless similar to original knob

but slightly, although almost undistinguishable noticeably, larger than

the original. Slipped new part on without the need of a tool.

Part was very pricey plus a hefty charge for postage / shipping.

Total approx. $65.00. Whew!!

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

When turning on the oven, I could see the ignitor red hot but it would not ignite the burner. I ordered the pair of new ignitor and burner tube. Upon removal of the burner tube, I saw a large hole in the tube where the center of the ignitor is located, clearly in need of replacement. Unlike some other ovens, the connector on the new ignitor was the exact fit for my oven (Hotpoint RGB745BEA7WH). After access to the tube, the replacement took less than 10 minutes not including watching about 3 youtube videos on how to actually do the replacement prior. You should turn the gas and electric off but ooops, I forgot. I was shocked at how easy this was!

My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!

Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.

Remove the warming drawer entirely. Remove all five nuts securing the valve and regulator assembly. Loosen (do not remove the nuts entirely) the burner assembly itself to give some wiggle room above the valve and regulator assembly. Also remove the single screw that holds the "collar" in place just above the gas outlet that services the oven burner. This should provide the margin of room you need to remove the valve and regulator assembly because it's a tight space. Working entirely in this cramped space (the warming drawer) will take time and patience. Don't drop any screws because you might create a whole load of more work for yourself. Loosen the brass nuts holding the gas lines in place. Then you have to maneovre the old equipment out. Just reverse all the steps to install the new equipment. Apply Harvey's to the brass nuts and re-attach the gas lines BEFORE you firmly attach the equipment using the five nuts. Don't tighten the brass parts all the way, just hand tight at first. Re-attach the equipment using the five nuts, then tighten up the brass parts with a wrench. Don't over tighten. Re-secure the screws that hold the burner in place. Then test the equipment. If all good, wait for the oven to cool, then do a final check that all the screws are firmly in place. Voila.