JFC2089HTB Jenn-Air Refrigerator - Instructions

Unsnap damper louver cover using only your fingernails at bottom. Remove two phillips screws from damper cover. Remove styrofoam molded insulation. Squeeze electrical connector to release latch; unplug connector. Release latches on both sides of damper control while gently pulling on damper control unit to remove it. Install new unit by doing above steps in reverse. Damper door may move when electrics connected; keep fingers clear.
Amana would not honor our extended warranty that we paid $65 for, saying that noises are not covered. Im glad that Partselect supplied the part quick and and a great price. The frig is quiet for the first time in 2 years!

First I removed the icemaker from the freezer by removing two horizontal screws holding it to the side wall, and one vertical screw holding the front to a bracket coming off the side wall. Then I used a flat screwdriver to unlock the electrical plug. (After doing this, I realized that this wasn't necessary at all, and this part could have been changed just as easily without removing the icemaker.) On the front, there is a white cover with Ice Maker Plus. Use a flat screwdriver to unlock the tangs and remove the cover. There are three screws in the corners that once removed, will allow the motor assy. to be gently pulled straight out. On the back of the part, you will see many gold lands that the timer touches. I don't think there was anything wrong with my motor. I had two spots where the gold plating was worn off, so I suspect it was not making contact, and the whole process would stop. Slide the new part in place making sure the teeth on the gears line up (not a big deal), and secure with the screws. Install cover and you're done. Mine has been making ice like it was brand new.

Remove cover inside frig at rearwall top with screw driver. Remove phillips screws holding unit in place. Unclip connectors ,and replace in reverse order.

I changed out the water valve behind the refrigerator that controls when the ice maker and water dispencer receives water. It was easy. I removed the lower back panel to get access to the valve. Pulled the hoses out by pushing up on the ring between the valve and hose and the hose came right out. I disconected the power lines. Of course the water was disconected and power plug out prior to starting the job. I replaced the valve and reconnected the lines and power. I put the back panel back in place and turned the water on to check for leaks. The next day I had ice in the ice maker.

Begin by turning off the water source from the wall, next using a line wrench, remove the brass water line fitting nut from the copper water line from the wall. Next remove the second water line from the plastic push fitting by depressing the fitting to release the water line. Remove the Styrofoam insulation piece that resides between the water lines that run into the refrigerator, then pull the old filter head out. Reverse steps for installation.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

It's good to note, first, that the dual water valve on Amana fridges are notorious for cracking and leaking, either due to the fridge being left in the cold (the water inside the valve freezes and expands, cracking the water valve) or from issues related to shipping. Read the reviews, here - it's a common issue, but easy and cheap to fix yourself. Here's my steps. I first turned off the water source to fridge by closing the correct valve. Next, I unplugged the fridge from electrical and from the water source line. When looking at the back of the fridge, I unscrewed the bottom left cover plate from the fridge body. After unscrewing and removing the plate, I made sure to note which lines came from which areas of the fridge and where the lines ended up at the dual water valve, and how they were routed through the plate and into the valve. The way this fridge is setup, the water source line screws into a main line that heads to the top of the fridge where the water filter is (like a "line in"). There's another line that heads back down to the bottom of the fridge (line out). The "line out" inserts into the outside plug of the dual water valve. The two lines coming out of the dual water valve are different sizes. Make sure to note which line goes to the icemaker and which line goes to the water dispenser inside the fridge. Once I knew which lines needed to go where, I grabbed my empty bucket, pulled the water lines out of the dual water valve with some pliers, and emptied the water into the bucket. After cleaning up any water splatter with my dry towels, I unscrewed the dual water valve from the plate. Once the old dual water valve was removed, I replaced it with the new valve and screwed it back into the plate. I cut off just a bit of the water line ends that were damaged due to pulling with the pliers, and then inserted them back into the correct spots on the dual water valve. I screwed the plate back into the fridge, reconnected the water source line (make sure to use some kind of water sealer tape or putty), plugged the fridge back into the electrical socket, turned the water source valve back on, and waited for leaks. No leaks! Once I was convinced there weren't any leaks, I had to bleed the water lines for about 20-30 minutes (it takes FOREVER...) by putting my bucket under the water dispenser inside the fridge and holding the water button for what seemed like an eternity - until the water was streaming steadily out of the dispenser. Voila! Good as new! Keep in mind that I didn't go through ALL the minute parts of each step - that would take too long. I'm believing that you'll be perceptive enough to catch the small things like looking at how the lines are routed into the dual water valve and where things are screwed into. Use your BRAIN, and you'll be fine. :-)

Inside the food section above the top shelf behind the light in the back, remove the lid from the cover in lifting from the lower edge no tools necessary here. Remove two screws with Phillips screw driver remove entire housing inclusive Styrofoam insert. Unplug damper Control Unit. Remove two screws and remove damper control unit and replace in reverse order. Finally that refrigerator is quiet, I should have done this long time ago. Unbelievable this is the second part I have to replace on this expensive refrigerator.

First, I removed the drawers at the bottom of the fridge and then I removed the three hex head (7/32) screws that hold the end cap on. Then I disengaged the slider which connects to the temperature control for the pantry drawer. Then, unscrewed the drawer slides with a Phillips from the old end cap. Also the slide push rod has to be disengaged from the clips on the back of the endcap.

Then, I reinserted the push rod to the new end cap and reattached the drawer sliders and the slider itself. At this point I realized I SHOULD have unscrewed the temperature slider at the back where it covers the cold air outlet. The screw had slipped out. I replaced it with a slightly larger wood screw. Reinstall the drawers, all done.

Since the crisper didn't come with a front, the old front needed to be removed from the broken cripser and attached to the new one. The easiest way to take off the front is to remove it from the bottom of the crisper. Once the pressure is released it comes off easy. Snap the front on the new crisper by starting with the top and snapping the bottom.

Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket
Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.

Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not the thermostat or adapter control.

This is the 2nd part I have bought for this refrigerator from Part Select. I wish the parts came with some kind of instruction. I had to re-use parts from the original equipment each time. After studying the replacement part I was able to figure out what I needed to do, but it would have been nice to have a little more information. There were 3 pieces which I needed to remove from the damaged piece and add to the replacement part. I would gladly pay more for a complete replacement part.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

I started by unplugging the unit, then removing the air outlet cover, then the housing & foam insulation. Next ,I disconnected the harnesses & unsnapped the damper assy., & put the new one in. Total repair time was about 10 minutes. I did buy the repair manual, but it was special order & arrived after I made the repair. I am an automotive technician, & this was a very simple repair for me.