JEACS50SLF2 Whirlpool Ice Maker - Instructions

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

I determined it was the cutter grid because there was a broken wire on the existing one. They have to heat up and cut the ice. I ordered it and the part was at my house in 1 day. The cutter grid part was easy to install. The ice maker is working great now.

Had repair man out to make repair his price for part $219.00 and $271.00 labor as he was looking up his price I got on line and found part here for $121.00 thought it might take me 1 hour to fix only 6- 1/4" nuts 2 screws and less than 30 min I had Ice maker working. Bottom line my total cost $75.00 repar man $121.00 part $196.00 that was a savings of $294.00

Remove ice tray and guard over moter. Un plug the 3 plugs and pull the entire motor assembly out. Use a screw driver to gently pry motor out. Snap in the new motor(the wiring was on the wrong side and the power cord coloring backwards on the replacement motor, but I snapped it in with the colors criss crossed and it worked). Re plug in the 3 plugs. Re mount mounting assembly, tray and then guard. Had a little trouble getting the tray back in. There is a little flap in the back that goes inside the tray. Other than that, a pretty easy fix.

I found the part I needed on this website, watched the tutorial and saw how simple it was to do myself. I ordered the part and it arrived within a few short days. It took me no more than 15 minutes to change out the part. I saved myself several hundred dollars. It is rather shocking how much the "professionals" charge considering the cost of parts, labor and nominal service fees.

what I discovered is the condenser fan is still operating but not strong another word insufficient cooling for the condenser. therefore, it's getting too hot and shutting off and stripped the circuit breaker. After installing the new condenser fan, it gets back in business. it's quite simple. Just unplug the unit off, uncover the bottom back cover and there you see compressor, condenser fan and other good stuff. there you unscrew the nut in front of the condenser fan and remove the fan, then it expose the two screws that holding the fan motor, remove these screws and take out the motor. and just install the new fan motor kit in and there you have it. plug it back to the wall and there it goes

I've tried ordering the part from Sears and they told me it will take about 7 days for the part to arrive, some other place said it will overnite for extra money. So I've ordered the part from Part Select at a good price and prompt delivery. once the part arrive installing the part so so easy cause it had easy to follow instructions.

UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.

Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.