JDB6510AWF Jenn-Air Dishwasher - Instructions

I took the bottom rack out of the dishwasher. I then took the filter guard and bottom spray arm out. Then I took the screws out of the filter guard to get to the rinse arm. I took the filter guard off, took the old rinse arm out and put in the new one. Have to make sure it is completely resting inside there. Then I put the filter guard back on. Put the screws back into the filter guard, put the two arm seals down around the rinse arm, put the bottom arm spray with guard back into the notches, put the screw top on so it can screw back in and the dishwasher is ready to go. Just make sure that you don't have a lot of soap built up, it will not clean the dishes right nor will the spray arms move. I had to call my appliance person out, and I have so much built up from soap, that I had to order a new filter guard and top and bottom spray jets. I now know to switch back to powder or liquid soap, because the tablets make a huge built up of soap... I have these parts on order now. In the meantime, I am cleaning out the jets with dishwasher magic and vinegar while I am waiting for my new parts. I now know how to put things back together so when I have this happen again I will know how to do it to save me the 63.00 office call and parts. I am happy that I know where to get my parts when I need them or break them by accident on trying to put my dishwasher back together again. Thanks.

I did not move the dishwasher out. It is a fairly tight space underneath, but the water inlet valve is located toward the front, so it wasn't too bad. The steps were:

1) unplug the power and turn off the water to the dishwasher.
2) remove the 2 wire connectors.
3) use the nutdriver to remove the 2 screws that hold the valve to the side of the dishwasher.
4) use a wrench (5/8") to remove the nut where the water goes into the valve. This takes some patience since you can't turn the wrench very far in the tight space.
5) remove the water outlet hose by using pliers to squeeze together the clamp and move it up the hose. Then twist the valve to free the hose and remove it from the valve. The nibs on the clamp are small and take a little time to get them squeezed together. If the hose has been on there a long time, you will have to twist the valve a few times to free it up.
6) now you will have to remove the sleeve that the nut was screwed onto. I had to take the valve to my vise to hold it. Then it wasn't too hard to remove.
7) use teflon tape before you reassemble. Just go in the reverse order.
8) hope there isn't a leak. Mine didn't.

The new water inlet valve seems to have fixed the problem!

As the screws took a special (non philips) head, I did need to buy a special one in the appropriate size (cell phone photos help!). Then I took off the 8 or so screws inside the front door, removed the two screws for the handle, replaced with new handle and screwed the front door back together. Not hard, would have been faster without the hardware store trip.

Located circuit breaker for dishwasher and turned off breaker to secure power going to unit. Removed water spray bar arm inside dishwasher basin by unscrewing center nut and unclipping tabs against arm. Removed sheet metal access panels on bottom front of unit. Removed two individual plug in wires to temperature thermister. Removed 4 conductor plug wiring going to motor. Removed ground wire going to motor frame. Located plastic handle which cam locks motor / pump assembly into place. Pulled handle down gently to unlock from detent and turned clockwise to release pressure on assembly. Removed motor / pump assembly from dishwasher enclosure. Installed all new parts purchased as listed above utilizing parts breakdown aquired from PartSelect.com. Reinstalled motor / pump assembly in reverse order as listed above. Tested and ran unit with no problems. Thank You PartSelect.com, Robert.

It takes about 5 min. to disassembled the lower jet system. As you disassemble, make sure you clean all the filters, and asses the integrity of the filters. If they are broken, you need to replace. Once you get to the impeller, you know it is broken because the lower part is loose. To replace you need to firmly hold the impeller as you unscrew the top screw. If the housing gasket is broken or too loose, replace. Otherwise you will have leak. Refer to your models diagram for proper assembly.

Took off old, snapped in new.

We ordered the replacement part for our Maytag model and when it came we saw that it was different than the original part. The original part had 8 wheels with a higher left hand side. The replacement part had only 6 wheels and no higher side. The replacement part would not pull in and out evenly and was a bit too narrower. We called Parts Select and told them our problem and they are going to refund us in full and take back the part they sent. Alas we will have to buy a new dishwasher. We would use Part Select in the future for replacement parts.
Alice
Cambridge, MA

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

I aligned the V-shaped tabs on the inner side of the part with the slots in the mating part and simply pulled the old part out (it was already disengaged from the wheels in the metal rail). I then inserted the new part into the slots. One side went in well, but the other side required the part to be bowed slightly to match up the V-shaped tab with the slot. Then the hard part was getting the wheels in position to snap them on. Once in position, it took a bit of effort to engage the snaps in each wheel. I was afraid of breaking the new part. These snaps are very stiff and even with the notch between them there isn't any give, but I was able to apply enough constant, steady pressure to finally get them to snap in without breaking.

Replacing my dishwasher racks was very easy. I followed the guidance on the PartsSelect.com website for replacing the upper rack. Replacing the lower rack was only challenging when I couldn't figure out how to remove the water sprayer from the old rack and place it in the new rack. A quick search on Google.com and I learned to turn the sprayer counter-clockwise to remove it and then clockwise to put it in the new rack. Worked like a charm! I would recommend PartsSelect.com to anyone. Easy to use, parts came quickly, and I appreciated the guidance from others.

I took apart the lower spray arm apart and removed the 6 hex screws. I noticed that the little plastic circle thing had been ripped off the dome-shaped thing. I replaced the part and put it all back together.

Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

I unscrewed the parts of the washing tower, then removed the housing and filters above the impeller. Lastly I removed and replaced the impeller and "o" ring. This repair went fine. Unfortunately another part (blower) let go and I decided not invest any more time or money into this machine since it was so old.

Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.