JCGS750SEF3SS General Electric Range - Instructions

Removed lower oven panel and replaced oven igniter.

Old school, so I first thought it had to be a thermostat, but realized it did not have a pilot light, but an igniter. Read a few stories of others who had the same issue. Ordered the part, came in early. By that time I knew what I had to do to replace it. Only issue was the part came with a male connector when the original was female. But part came with a couple of ceramic wire nuts, so I guess that is not uncommon. Cut the connectors off and used the wirenuts. Oven is working well.

This repair was so easy!! I found the part we needed on line with no problem, then I found Parts Select, saved $20.00(honest!) The part was here in 2 days, I bought beer ,called my brother in law and from the call to the oven working was less than an hour. Didn"t break a nail,

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

Every part of the part replacement was easy with the exception of removing one of the two screws that were holding the igniter to gas bar. No fault of the part to be replaced in any way. One of the screws that hold the igniter to the gas bar stripped when I was attempting to remove it. Had to use a small cut off wheel and my dremel to cut the screw and then was able to remove it by screwing it all the way through the hole it was in. Then tapped the two existing screw holes to 10/32 and attached the igniter with new screws. Everything else was about as easy as you can get.

First removed 3 screws at burner front and back then pulled out lower storage drawer to disconnect plastic connector, removed and had to cut plastic connectors to use ceramic wire nuts (supplied with parts box) I had to work from underneath stove as well as in the oven it self, if the main door is easily removable it would have helped a great deal but four hours later

I got my part in a couple of days during christmas and still got at pretty quick it was 5 screws unpluged the old one pluged in the new one put screws back and we were ready to cook, did all from inside the oven did not even move the stove very simple!!

Had to use the wire nuts because the plug did not fit.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.

I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

The job was made very simple primarily due to the repair video that was available on your site when I ordered the part that I was looking for. The job can be done in less than 15 min, but it took me a little bit longer because of some rusted screws that didn’t want to come out so easily. I also decided to take of the front door (not mentioned in the video) just to make it a bit easier to reach the igniter component. The door comes off very easy by opening the door about 6 inches and pulling up and off of the door hinges. Again for a novice like me the video was a life saver.

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!

I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?

The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.

Although the original oven design called for a round igniter, the most recent replacement, done by a service mechanic, utilized a flat igniter. I compared the appearance of this flat igniter to the igniters offered by PartSelect and found that the GE igniter (not the Roper which cost twice as much) matched exactly. I installed it and that solved the problem (of insufficient igniter heat to turn on the gas).