All Installation Instructions for General Electric Range JBV42G3H2

broken light socket

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Parts Used:

RECEPTACLE PUSH-IN

James from Monterey, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Poor connection to element

In a little over 15 minutes, I was able to pull the element and pan, snip the wires on the terminal block and use the wire nuts to fasten the new terminal block. The shrink wrap tubing went into place easily and all went back together easily. Best of all, the two year problem of a poor element connection was solved in a matter of minutes for a few dollars.

Parts Used:

Range Terminal Block

Austin from Blackfoot, ID
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

the center of the element had broken

just pulled the old one out and replaced with new one. very easy

Parts Used:

Surface Element - 6 Inch - 240V

Betty from Fayetteville, WV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

No Problems

I removes the old element and drip bowl, then replaced the drip bowl, then replaced with the new element. Approximatly 3 minutes. . .

Parts Used:

Surface Element - 8 Inch - 2350W

Jerry from Copperas Cove, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

broken nylon retention pin in upper oven door

Removed 3 lower screws holding the upper oven inside door panel to the door frame. There is enough flexibility in the panel to coax it away from the frame at least an inch. Removed the old nut plate from inside the door and replaced it with the new one. Screwed in the retention pin and 2 washers while holding the nut in place. Assembled the 3 lower screws to complete the assembly.

Parts Used:

Door Strike Assembly

john from cincinnati, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set

Was this instruction helpful to you?

I needed to replace the 6" surface unit.

My GE range is 20 years old, and still going strong. All I needed was to replace the 6" surface unit. After making slight adjustments, it was just a matter of placing the new unit. After finding this Co. on the internet, and checking others, I will certainly order from Part Select again!Dorothy Trakshel

Parts Used:

Surface Element - 6 Inch - 240V

Dorothy from South Daytona, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

older element losing heat

really easy, remove old and replace with new...easy, once you have ordered and received the correct part.

Parts Used:

Surface Element - 8 Inch - 2350W

Joan from Wilmington, DE
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Original trim ring did not fit

I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.

Parts Used:

Trim Ring - 6 Inch

Sarah from San Andreas, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I could not find a dealer who could tell me what part I needed because the model was discontinued

I just went to your web page and indicated I needed an 8' surface element and up popped a picture; I ordered it and plugged it in and it works perfectly. I didn't need a model number, or a part number. Three cheers for a simple solution and a 1st class web page!

Parts Used:

Surface Element - 8 Inch - 2350W

June from Merritt Island, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Broken heat element

Fit was perfect, slip right in prlace and works great thank u! R.e.Rice

Parts Used:

Surface Element - 6 Inch - 240V

robert from wernersville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

surface element not working

I simply pulled the old surface burner out, and plugged the new one in. It took less than one minute! The amazing part of this repair, is actually that PartSelect sent the replacement surface element burner OVERNIGHT! I could not believe it, and was VERY impressed with their commitment to help their customers in time of crisis. It arrived just on time for my Thanksgiving not to become a nightmare. Thank you PartSeclect!

Parts Used:

Surface Element - 8 Inch - 2350W

Claudine from The Colony, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven light wire broken, damaged socket

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

Parts Used:

RECEPTACLE PUSH-IN

Patricia from Brandenburg, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Scorched Element

It wasn't so much the repair that was needed as how impressed I was with the fast delivery. Without a fourth burner & a holiday weekend coming up I was in desperate need of my element. I ordered it around 1:00 pm on a friday & it was delivered the next day before noon! Very impressed with the ease of ordering & receiving. Thanks again.

Parts Used:

Surface Element - 8 Inch - 2350W