JBS55DM5WW General Electric Range - Instructions

I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried the oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.

I first turned off power, then I removed the old top oven heating element, I connected the new element to power supply then placed the element back into holders.

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

Remove 2 screws and 2 wires- took the coil, then installed the wires and put the screws in--works fine. Thanks for the fast service.

I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.

Took me a second to remember that YouTube is just as handy a tool as what I've got in my toolbox. The installation of the new glass was as easy as apple pie. Anybody that has ever used a screwdriver could manage that fix and do so single handedly. PartSelect.com came through with an easy-to-navigate website, a very reasonable price range and anything you could ask for to help fix whatever has broken. I quoted a gentleman in my town, a handyman, and he came back with a price tag of over $300 for parts and labor! Even with tax, shipping and the new glass I came in well under $100, and the labor was next to nothing. If i ever have to replace or fix something in my house again, I'll be using them, Without a doubt. Thanks for everything, dudes. Cheers!

Watched youtube video. Very easy to replace

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.

Performed repair using a video for reference.

threw out the old ones and slide in the replacement ones from you.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

The new element didn’t come with instructions, but a previous customer had left a review on the website that he had found a helpful YouTube video. So, I also found a video that walked me right through the steps.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.