Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JBS55DM2WW > Instructions

JBS55DM2WW General Electric Range - Instructions

All installation instructions for JBS55DM2WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JBS55DM2WW
211-225 of 298
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Range lower drawer would not stay on track.

  • Customer: Richard from Newark, DE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Easy to install replacement parts using the screws provided.

Oven Glass Door

  • Customer: Gaetano A from Hamden, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Making repairs on glass is not always fun to do especially when you have make sure what the right torque is.. My decorative glass broke and I reached out to part select for a new one. They had exactly what I needed for the perfect price. Not too difficult to replace just do not over tighten, this might cause the glass to break again.

Rust on Bottom of Oven Door

  • Customer: Nat from Irvine, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Self-clean the oven or use Easy-Off. Lay some towels or other padded ragging on the kitchen table. Open the oven door and lock the hinges. Pull the door out of the oven and lay it on the table with the oven handle hanging off the edge of the table. The inside of the oven door will be face up on the table. Use the 1/4 Nut Driver to remove three sheet metal screws from the bottom of the door. Use the T10 to remove two long screws from the top inside of the door. lift the door guts and set aside along with the 5 screws and two spacers you found under the top of the door. Use the nut driver to remove 4 screws holding the Door Bottom Channel Trim. The door handle and side channels will fall off (catch and set aside). you are left with one piece of glass with the old bottom channel trim. Gently tap the lip of the channel with a screwdriver in a towel to slip it off the glass. Gentle patience is a virtue here or the glass will break. Clean the glass with CeramaBryte or equal to get the burnt oven goop off. (While you're at it, do the same to the bottom of the door guts above.) Slip the new bottom channel on the glass as far as it will go (not very far in my case) and replace the door handle and side channels. You will see that the holes line up pretty well without having to jam the bottom channel onto the glass. Screw (4) the side channels to the bottom channel. Replace the Door Guts, being careful to line up the two spacers at the top of the door. Three screws in the bottom of the door, then the two Torx screws back in the top of the door. Put each screw in just finger tight and after they are all started, screw them home. Slip the reassembled door back in the oven frame, flip the locks up and Voila! Now that it's over, let me just say that if a camel is a horse designed by a committee, this thing must have been thought up by the US Congress!

Replaced oven element

  • Customer: Jeffery from Meyersdale, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Turned power off. Pulled stove out. Took two 1/4 inch bolts off element inside oven. Removed 5 1/4 inch bolts out of panel on back of stove. Removed clips on element. Installed new element.

Spilled 1/2 gallon Hot wax on stove

  • Customer: Roman from West Chester, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

lower oven element burnt through

  • Customer: Roger from Laramie, WY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Unplugged the range and tested for current, removed the two mounting screws, unplugged the terminals and replaced with new element. Plugged the unit back in and tested for function. A-OK. Selection, ordering and shipping all went well, again. Thanks.

dead mice in insulation, chewed wire on latch switch

  • Customer: Don from Flagstaff, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
replaced insulation

The buld broke off in the scoket

  • Customer: victor from Henderson, NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Had to replace the socket. Once I realized I had to move the stove away from the wall and do part of repair from the rear it went pretty fast. I removed 2 screws from inside the oven but had to remove the electrical connections from the rear. then replaced the socket, reconnected the electrical connections. and replaced the cover.

Bottom oven element burned out

  • Customer: Thomas from Enin, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Ordered the part from Part Select (and their web site was very specific and had everything I needed to make sure I selected the correct part number) Received the part the day after I ordered it without any special pricing for fast freight. Was very impressed with the service and product ordered. Received it - followed the instructions from people that had order the same product from Parts Select and posted on Parts Select - unscrewed two screws - unplugged the old element - plugged in the new. Had the wife baking pies in about 15 minutes!!!

Broken drawer support

  • Customer: Mario from Deer Park, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Heating element burnt out in oven

  • Customer: Dorothy from Kansas City, MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed 6 screws from the back of the stove, removed the panel and attached the new part. It was a breeze to fix and my oven is back in working order.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

F2 error when oven was heating up, along with a beeping noise and then it shut off

  • Customer: Lori from Paris, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Element was burned out

  • Customer: Jerry D. from Monroe, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
replaced with a new element. real easy to change. had very fast shipping will consider PartSelect again in the future.

Burnt out Baking Element

  • Customer: Christine from Palm Bay, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
My Son-in Law replaced it for me. Great Job and wonderful Service from you people, I was very pleased.
All Instructions for the JBS55DM2WW
211-225 of 298