JBP61DB1WH General Electric Range - Instructions

I ordered it on line and it was easy to fix, I had it done before my husband came home from work. I just undid the old one and pushed the new one on. I have to stay ordering from here was alot cheapier

I ordered to correct part from PartSelect with relative ease given I know nothing about oven repair. What's even more amazing, my wife who is not mechanically-minded, took the element home and replaced the broken one in 15 minutes with nothing but a pair of pliers. We live 22 miles from town so a repairman would have cost over $100 just to show up. Total cost = $36!

I don't know, my husband did it. But he said it was easy and he used a nut driver and flathead screwdriver :)
PS...partsselect saved us money and saved the stove from the landfill!

removed the two screws pulledthe element out disconnected the two wires put wires on new element put the screws back in.

shut off power, removed self tapping nuts, removed element, put new element in, re-attached nuts.

With the oven unplugged, I removed the protective plate from the back of the oven, and then I unplugged the old element from the contacts. There were two screws holding in the element inside the oven- after unscrewing these, the old element slid right in. After reconnecting everything and plugging the oven back in, all was good. Pretty simple.

My Husband did the repair. It took him longer to prepare the appliance than it did to perform the actual replacement of the bake element! We LOVE the service and the selection found at PartSelect!! Our part arrived within 24 hours!We've recommended you to all our friends and co-workers. Bravo! Thank you again.

Removed the cover plate, pulled the element out, removed the screws holding the wires in place, but then I had to enlarge the screw holes on the new element in order to fit the screws into the new element. Took a while with an awl to enlarge ther two holes. Connected the new element, pushed it back in and replaced the cover plate. Worked great.

First i removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Very simple and easly job.

Disconnect power to range, remove fan cover (4 screws).
Remove old element (2 screws).
Pull off wires from old element.
Discard old element, clean bottom of oven.
Slip wires on terminals of new element.
Install new element,and fan cover.
Reconnect power.

Used a nut driver and removed to studs and pulled the old element out and disconnected the two wires. Then connected the new element and put the studs back. It was that easy. Great website and it only took 5 minutes to order the part and received it on time. Plus my wife was trying to cook thanksgiving dinner. Thanks

Removed oven door and racks. removed fan cover to expose elements two retaining screws.removed retaining screws and pulled burned element forward to expose electrical connectors.unconnected slide on connectors from old element and pushed leads onto new element and re-assembled.

I first read the repair stories on this website. I turned off the power to the range in the power box. I removed the 2 screws, pulled out the old heat element a little, then disconnected the wires from the connectors. I just reversed the steps to put the new one in and viola. Really simple. Parts came really fast too. At first I ordered the wrong part b/c I didn't look up the part using the model number, I just went by t he picture and the manf. name. I returned that and got refunded promptly, so make sure you order by model number b/c parts are made different for each appliance model.

First, used the nutdriver to remove the two screws that hold the element. Then pulled out the element 4 inches. Disconnected the two wires from the old element and discarded it. Connected the wires to the new element and tightened them a bit by squeezing with pliers (not too tight, but just enough so they won't disconnect easily). Pushed the wires back through the insulation and screwed the two nuts back in place, making adjustments so that the element is level.

I had a great experience with part select. The part was easy to find and arrive within two days in perfect conditions. Everything went smoothly with the repair and the element is working very well.

Simply slide stove away from wall and unplug. Remove the center back plate on the rear of the stove, Open oven slide new element into rear of oven, snap into place. Return to rear of oven. slide wire connectors onto oven element prongs, replace center cover, make sure oven is turned off, plug stove back in and slide back into place. Open oven and turn on. allow element to heat up. Once the element has heated and the new burns off. Turn off the oven and replace the racks, This entire process took maybe 5 minutes.