JBP26BY4 General Electric Range - Instructions

Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!

It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!

We simply typed in the model of the range and several selections of replacements came up on your website. We ordered the black porcelain ones to replace the old chrome ones, thinking they might hold up better and be easier to clean. They look great and I really think they WILL be easy to wipe up. Thank you, Part Select! Patty in Indiana

For 12 years I've been suffering with the incorrect burner bowls...I love to cook and it's really irritating when your bowls don't fit correctly. Now, I am amazed at how my burners fit! Thank you! What a Blessing!

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

Remove the front panel, at which time the spring loaded door slammed closed while the paned and handle were in my hand. Fortunately I had a star bit to fit the screw holding the door and panel together.The parts should come with 2 screws since the part has holes for 2. note: the factory installed handle only had 1 screw in each side.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Good directions

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

took the two bolts out of element, pulled the wires and replaced...It was the fast shipping and receiving that made it awsome.. was all done in 2 days..thanx

Took the upper back covering off, disconnected the clock control. The only problem is the replacement didn't have the same connections so I was able to pull up the replacement number of wb27x10311 and asked for a diagram which told me exactly where to plug each of the red, white, blue and yellow wires, what a relief! To my amazement I fixed my "old" stove for less than $160, if I had called GE to service it, I'm sure I would have been looking at a $400 bill. This was the way to go, Thank You!

After needlessly replacing the Thermo-sensor and Bake element I was able to determine that, while I had proper voltage to the appliance I did not have power to bake element when bake knob was turned on. The broil element worked properly. I hesitated purchasing the Electronic Clock Control because there was nothing wrong with the oven clock and it was an expensive part. I switched out the control unit and was delighted to see the bake element heat up immediately. It was simple to replace and the instructions that came with it were adequate - just some differences in the color of wires. Thank you Part Select.com!

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.