JB735DP2WW General Electric Range - Instructions

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

This repair is really easy unless the trim piece has rusted so badly that it's attached itself to the front door glass. It took a long time and some WD-40 to pry the trim off w/o breaking the glass. REPAIR: Remove the door and lay it on a flat surface. Unscrew the 3 bottom screws w/ small pliers, then unscrew the top two inside door screws w/ a small metric allen wrench. Remove the door trim to get to the last four side trim screws. Once the old trim is out just clean up any residue/rust remaining on the glass, install the new trim and reverse the steps to put the door back together. If the old trim comes off easily it should only take @ 20-30 minutes.

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Self-clean the oven or use Easy-Off. Lay some towels or other padded ragging on the kitchen table. Open the oven door and lock the hinges. Pull the door out of the oven and lay it on the table with the oven handle hanging off the edge of the table. The inside of the oven door will be face up on the table. Use the 1/4 Nut Driver to remove three sheet metal screws from the bottom of the door. Use the T10 to remove two long screws from the top inside of the door. lift the door guts and set aside along with the 5 screws and two spacers you found under the top of the door. Use the nut driver to remove 4 screws holding the Door Bottom Channel Trim. The door handle and side channels will fall off (catch and set aside). you are left with one piece of glass with the old bottom channel trim. Gently tap the lip of the channel with a screwdriver in a towel to slip it off the glass. Gentle patience is a virtue here or the glass will break. Clean the glass with CeramaBryte or equal to get the burnt oven goop off. (While you're at it, do the same to the bottom of the door guts above.) Slip the new bottom channel on the glass as far as it will go (not very far in my case) and replace the door handle and side channels. You will see that the holes line up pretty well without having to jam the bottom channel onto the glass. Screw (4) the side channels to the bottom channel. Replace the Door Guts, being careful to line up the two spacers at the top of the door. Three screws in the bottom of the door, then the two Torx screws back in the top of the door. Put each screw in just finger tight and after they are all started, screw them home. Slip the reassembled door back in the oven frame, flip the locks up and Voila! Now that it's over, let me just say that if a camel is a horse designed by a committee, this thing must have been thought up by the US Congress!

Installed new guides with a nut driver without any problems.

Easy to install replacement parts using the screws provided.

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Followed the instructions that were sent to me by E-Mail.