JB700SN1SS General Electric Range - Instructions

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.

I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

replaced Plastic Guides

One wire at at time then used my razor blade to get front off stuck right back on

1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.

Ordered the part, it arrived and 5 minutes later it a complete installation

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Took the old racks out andcslipped the new ones in

First of all, there are FOUR panes of glass on the oven door and two different sizes. Make sure you're ordering the right pane. We initially got the wrong one and had to return/reorder.

Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful when putting it back together.
When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.

For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.

We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.

First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above