All Installation Instructions for General Electric Range J2C968CEK3CC

very easy

there were no grate pads so it was easy to add them.

Parts Used:

Grate Foot

ROBERT from CYPRESS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The Grate foot is to big for the hole.

I had to drill the hole to a larger size to enable the foot to fit.

Parts Used:

Grate Foot

Harold from Broadalbin, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light bulb went out,could not find replacement part.

Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.

Parts Used:

Halogen Bulb Kit

Gregory from Pearl River, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.

Nothing technical.

Parts Used:

Grate Foot

Chelagh from Fredericksburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Oven will not heat

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Parts Used:

REAR SUPPORT

Joseph from Homosassa, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Grate foot bdroke off allowing grate to scratch cooktop

Used scribe to remove grate foot plug still in grate inserted new foot.

Parts Used:

Grate Foot

John from Tijeras, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Broken Probe Sensor

Replaced it

Parts Used:

Meat Probe Thermistor

Michael from Tucson, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Leaking from front door

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Parts Used:

Grate Foot

Gene from Simi Valley, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Burners are supposed to burn with a blue flame. Two burners had yellow flames

New burner Heads repaired the two yellow burning units. I believe heat caused the old heads to become. warped over time.

Parts Used:

HEAD BURNER B

Don from Port Orchard, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Parts Used:

REAR SUPPORT

Mario from Deer Park, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Range lower drawer would not stay on track.

Easy to install replacement parts using the screws provided.

Parts Used:

REAR SUPPORT

Richard from Newark, DE
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Stove drawer rear guides broken

Installed new guides with a nut driver without any problems.

Parts Used:

REAR SUPPORT

Robert from Shakopee, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

gasket on door was brittle

I feel like Macho Mom. I called in the repair guy since I was afraid of dealing with the gas. HE repaired one item but could tell I was comfortable fixing things and pointed out that the gasket was brittle and would cause major problems if not replaced. Took longer to order the part than do the repair, don't know what I was afraid of!

Parts Used: