J2B918CEK3CC General Electric Range - Instructions

I removed oven door so i could reach easier. Then removed screws from Broiler element at the back of the oven. Pulled off connected wires. Slid wire connectors on new element and screwed bracket in.

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.

every thing went great

Replaced old with new.

I unscrewed two screws inside the over over the element. Then I slowly pulled the element out and unplugged the two wires attached. Afterward I pushed the element back in place and screwed it back in and was done. Sure saved $550 I thought I might have to spend on a new oven,

i dd not notice at first and started the self cleaner,,,i notice the self cleaner did not work,the screws had to be sprayed with dw30a couple of times and a pair of pliers to remove screws(no wrench set)after removing screws pulled the wires out to see and removed the connection to wires,,,replaced with new bake element and replaced the screws works fine,,,by the way i am a 64 years old grandmother

Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.

Performed repair using a video for reference.

Lift out old one and replace with new one. Also ordered an additional oven rack.
Their website is super easy to navigate and their availability of parts it's outstanding!!

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Followed the video and it was fast and quick.