IUD7070DS1 Whirlpool Dishwasher - Instructions

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

The old filter simply unscrews and the new one screws in.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

The top and bottom parts of the lower wash arm were separating. This caused water to spray out the ends of the wash arm and come out the front of the dishwasher. In addition this water was not spraying upward resulting in dishes not getting cleaned. Took me a while to figure this out but the repair was simple.

like the instructions showed

Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.

The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine