IDF320PAFW0 Whirlpool Dishwasher - Instructions

Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.

The spray arm repair is super easy. Just click & turn to remove the old arm, repeat to install the new! Less than 2 minutes total time spent on the repair.

Just snap it in

quick and easy,tine-row just snapped right in! Took about 15 seconds!

Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!

Installed brackets

I loooked up the main problems associated with that model which is provided on the website and ended up ordering a heating element and a thermostat. I replaced both parts it took me about 30 minutes. The dishwasher is working again and my wife is very happy. Thanks guys!!!

Solution was very simple with the side mounting bracket kit, the only problem was somehow one of the brackets was damaged out of the box . There's a slight off-set on the bracket to allow it to fit properly next to the dishwasher but this one had been flatten out. Had to have happened before going into the shipping box because they were very well protected with bubblewrap. Also, brackets are fairly heavy gage metal so it would have taken some amount of force to do this. Fortunately I was was able to bend it back into a useable shape. It wasn't perfect to look at but because it's mounted behind the side of the dishwasher it didn't matter as long as it worked.

I pulled the dishwasher out from the countertop rolled it to the side removed old clamps and hose installed new hose in kind used different hose clamps than provided turned up right pushed back in ran a cycle while looking underneath with a flashlight and saw no leaks and dishwasher has been back in use for a week now.Chris

Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.

Very simple repair when you're supplied with the proper parts. Their delivery time is exceptional !

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

shook bottle and painted waited a day and repeated

My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.

We had to pull the dishwasher out the get the heating element brackets loose underneath. We had to put the new heating element in and then we had to figure out which code to program in to make it reset. the last one listed on the installation instructions was the one that worked. I think it was heated dry, normal, heated dry. It would be very helpful if the reset instructions were put in the manual by whirlpool. I am very pleased with my part that I ordered from PartSelect. It came within 2 days of placing the order.