IDF320PAFW0 Whirlpool Dishwasher - Instructions

The old filter simply unscrews and the new one screws in.

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

The dishwasher stilled filled with water and drained. after verifying that the unit was mostly empty of water, I placed the unit on its back. I removed the main pump leaving the wire terminals in place so I could energize the pump out side of the dishwasher (cut with diagonal cutter). I energized the pump and found that it ran. I noticed that the impellor had significant movement side to side. I suspected that the impellor was jamming in the pump housing. I ordered a new pump from Parts Select. I installed the new pump and reconnected the electrical. The dishwasher operation was restored.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Very easy to twist off the old pump and replace with new part. Worked perfect after replacement! We just followed you tube instructions

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

removed and installed cords with screw driver