HTDP120ED6WW Hotpoint Dryer - Instructions

easy to fix took less than 10 minutes

Followed your video instructions and it worked exactly as described. You will be my source for all appliance repair parts.

Snapped right into place , less than a minute, if that

UNPLUGGED THE DRYER AND PULLED THE DIAL FROM THE START SWITCH. REMOVED THE FOUR SCREWS FROM THE TOP OF THE CONTROL PANEL WITH A T20 STAR SCREWDRIVER. PULLED THE CONTROL PANEL COVER FORWARD. LABELED THE THREE WIRES GOING TO THE START SWITCH WITH THE NUMBERS ON THE OLD SWITCH. PULLED THE WIRES OFF THE OLD SWITCH. LIFTED THE RETAINING CLIP ON THE OLD SWITCH AND ROTATED THE SWITCH ABOUT 90 DEGREES. PULLED THE OLD SWITCH OUT AND INSTALLED THE NEW SWITCH, ROTATING IT UNTIL THE RETAINING CLIP SNAPPED INTO PLACE. CONNECTED THE WIRES TO THE CORRECT NUMBERED TERMINALS ON THE NEW SWITCH. PUT THE CONTROL PANEL COVER BACK IN PLACE AND REATTACHED IT WITH THE SCREWS, REPLACED THE DIAL AND PLUGGED IN THE DRYER.

I remove the know, slid the old timer out, leaving the wires connected. Placed the new timer into position and secured it, then unplugged wiring one at a time, placing them onto the new timer. All went great.

Easy peasey! Just Removed/Replace screw-in type bulb.

Unplugged the dryer. Removed the 4 star headed screws with a screwdriver. Tilted the console forward and lifted. I didn't have to slide mine to the right. Pulled the knob straight off the front of the console. Lifted the lock tab with the needle nose pliers and twisted the switch to the right. It popped right out. Pulled the wires off with the pliers. Be aware, there are three wires, two red and one black. The both red wires only connect to one terminal on the switch. It looked at first glance as if I had the wrong part. But those two wires are connected to each other so it was correct. Plugged those wires back on. Put the switch into the hole and twisted it back into place, the lock clicked in to place. Replaced the console and plugged it back in and it worked perfectly. Turned right on. This took me under 15 minutes to do. Steve is the man! This girl has been able to use his videos to repair the dryer 3 times, the washer once, and my dishwasher 3 times over the years!!

Removed the broken lint filter and replaced with new

Based on the few components in a dryer, I diagnosed the problem as a defective timer switch. Five screws remove the rear cover. The timer switch purchased was the identical part that was currently installed. In the old days, I would have drawn a picture to note the wiring connections. These days, we just take a picture on a cell phone. I removed the switch from the dryer and moved the wire connections one at a time over to the new switch. When all of the connections were in place, I installed the new switch. With cover still removed, we tested it and the dryer shut off as it should. Super easy repair. The only thing I would have done differently is I should have purchased a replacement knob and retainer - the original had cracks in the plastic that I didn't know about until re-assembly. Superglue took care of the knob, but I should have replaced it too. Disconnect the power cord first, take your time, and be careful with the sharp edges of sheet metal. I suffered an ugly cut on my finger but I'll survive. Super easy repair. She'll think you're a hero since she didn't have to call a repair man.

With the help of doityourself guy on the internet

YouTube showed me just what to do. I unplugged the dryer and took the back off. Then I took a picture of the timer with my phone since there were about 6 different colored wires that had to be unhooked and put back in the right place. It was not difficult. Last I turned the timer in the bracket so it was secure. I also had to order a new dial since the old one was split from years of use. A repairman would have charged for the call out plus the parts so I saved money by doing it myself. P.S. I'm a 71 year old woman.

Followed the directions in the video. The only problem was there was no mention of needing a star bit set in addition to a Philips screwdriver in order to get the back splash detached from the dryer. This is probably because the machine was 11 years old. It would have been more helpful to have a note that machines prior to a certain age would need that tool. Otherwise it was a easy job even for a 75 year old grandmother.

Gently pull off all knobs and put aside. Remove the panel screws using the star bit. Tip panel forward. Remove three wires from old switch and put them on same terminals on new switch. Use the screwdriver to gently pull up the old switch's locking arm from the slot in the front panel and rotate the old switch until it pops out of the front panel. Insert the new switch into the panel and rotate until the locking arm clicks into place. Replace front panel making sure no wires are pinched. Re-install the front panel screws and control knobs.

Shortly after a piece of felt (the duct felt seal) was visible on the drum intererior, the dryer started making metal-on-metal squeaks. A few weeks later it started leaving'machine part' type brown/black marks on clothes. With the model # it was quite easy to find and order the correct part, which arrived a few days later. The accompanying video made installation quite straightforward, even for someone who's NEVER worked on a dryer before - even though the model used wasn't the same. Over half the repair time was to clean out lint and dirt from the various exposed parts. Overall, an easy and effective repair that solved the staining issue. Follow the video and you won't go wrong.

After speaking with your representative and him explaining how to me how simple it would be to switch out this light socket myself. I went on y tube went through the instructions and had to go buy a new dryer. And before you jump to any conclusions I can and do repair and and all of things around my house. I will NEVER purchase anything from you company again ander the pretense that it is so simple. This should have been told to me that an election should have done the job!!!!!! Now not only am I out the money I paid your company but I’m out the money I shelled out for a whole new dryer. I am a very angry customer and I would never recommend you to anyone!!! EVER!!!