HDA2000Z05WH Hotpoint Dishwasher - Instructions

The replacement of the motor and pump assembly went smoothly and without difficulty however this did not fix the problem. It then appeared that the inlet water valve was not operating properly, so this part was ordered and instlled, a very simple proceedure that could be done witrhout removving fthe dishwasher from its cabinet. -- Again failure to run -- the timer assembly and electronic panel were then removed and examined. The control panel had no visible defects, so the timer assemblyand its cover was removed and examined . Uing a variable power supply the drive motor for the timer was energized and tested. As the motor ran properly the electrical switching contacts were then carfully checked, it was discovered that one contact set was heavily pitted and burned. These contacts were carefully cleaned and pollished with 1000 grit sanding paper. The actuator leaves were examined and two sets were found to be slightly out of alignment. The leaves on these sets were bent slightly to insure they were in line with the rest of the leaf serts. It was then noted that the rotating leaf('s) actuator had a home position indicated by a molded depression at one location and the motor was energized using approximately 5 volts ( a nine volt battery could also be used as a poer supply) observing prolper polarity to run the rotator until the home position was established and the actuator rods paul dropped into this depression. The assembly was then replaced in the diswasher using care to make sure that the actuation arm and spring were positioned properly weith the arrow end of the arm located in the recesss of of the rotating timer disk use care in placing the assembly and do not lose the sping which attaches to a mounting post and the arm. You may want to take a picture of the spring and arm locations when you rwmove the timer assembly to properly re-assemble all components, the repaired unit was placed back in its cabinet and a full cycle run to establish proper operation. And unit checked ok! Some of these proceedures are not for the weak of heart. I am a retired engineer who has been repairing my own equipment since graduation. .

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

We bought a used dishwasher that appeared to be in good shape. After installing I ran it through its cycle. It seemed to work fine but after the wash cycle it would not pump out to drain. I found there was a solenoid that controlled the pump direction (drain or to the washer). It tested to see if it was getting power when it was supposed to pump to drain and it was. When I manually actuated the valve the dishwasher pumped out as it was supposed to. With power to the solenoid and the valve working as it should the only peice left was the solenoid. I ordered it from PartsSelect.com and it arrived in 2 days. Installation was only 2 screws and a spring and all now works great.
The on-line parts diagrams and fast shipping make PartsSelect the only choice when buying parts for my appliances.

I went to your site and check all the diagrams and then read the postings from others. I turned off the electrical breaker then took off the lower cover of the dishwasher. After disconnecting the water and electricial connections I was able to remove the 2 screws holding the unit in place and it came right out. I turned the unit over and was able to just remove the old part and put the new part in place. The whole job took me about one hour but I had never worked on a dishwasher before. Your site made the repair very easy to do on my own.

I took the inside of the door off of the dishwasher and disconnected the timer, ordered the new timer and with a couple of screws and the attachment of 3 wires I was back in business! Now my dishwasher is working better than ever!

After checking to make sure the filter wasn't clogged I removed the faceplate and, poking around a bit realized that the solenoid that actuates the drain valve was jammed. Removing it was was simply a matter of removing a pin and two screws. I reattached the new part, the only difficult part was holding the part in place while reattaching a few springs. Closed it up and its working like a champ.

I replaced the drain solenoid which was about $35 dollars. It consisted of a couple of springs, a hanging bracket, a plastic part and couple of screws to fasten the bracket and the solenoid of course. My dishwasher now drains the water. Much easier fix than i thought it would be.

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.

I had a problem where the GE dishwasher would randomly stall upon startup due to a dead spot in the motor which prevented it from energizing. I removed the dishwasher's bottom access panel to inspect it and found that not only was the motor dead but it had a sizable leak emanating from the pump seal. I removed the dishwasher from under the cabinet area and turned it over to make it easier to replace the motor and pump assembly which only took a matter of minutes; the most difficult part of the repair being the reinstalling of the dishwasher. The replacement motor/pump assy was not only modified from the original parts but it is also much quieter than the original. I also have to commend PartSelect on their very speedy delivery which was only 2 days. All in all with a couple of minor modifications that was taken care of with the included parts the repair went very easy.

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.

I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.

Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!

Recieved universal parts f/ pump & mtr assy. sorted them out, picked the ones I needed to complete my repair. Installed new assy, checked operation and was completly done in about an hour.

My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.