GYE22HBLETS General Electric Refrigerator - Instructions

Removed drawers, lifted out old frame assembly ( no tools ) removed and cleaned old glass from assembly.
Carefully screwed old rollers ( x4 )into new frame, then placed old glass in new frame, repositioned frame into refrigerator and then repositioned drawers in frame.
20 minutes , no issues

Popped it up and popped new one on

It was very simple. Removed 4 screws on top of door where panel is located. Unplug 3 three connectors and removed board. reinstalled new one in reverse mode. On the down side this did not solve the problem. I am still working on it.

Ordered a replacement ice maker. Simple to remove old unit one screw and one screw to remove wire cover to unplug. Replacement unit looked a little different as the left side of the new unit had various ridges which did not allow a proper fit into ice making box. After examining old unit and new I swapped the old left cover with new left cover and unit fit perfectly and it is working correctly. I suggest adding a quick note about the upgraded part as it may not fit properly and the side cover may have to swapped out.

Removed all containers from the freezer,
Removed lower freezer door, 3 bolts on each side.
Removed one front screw on the ice maker, unplugged two connectors on slide off unit
Removed covers on the old ice maker and installed on the new one
Installed the new ice maker in reverse of the removal process

Inspected the old ice maker and found the motor drive gear had missing teeth; I believe that the heater on the ice maker was failing causing a strain on the drive gears

Exposed evap defrosted with heat gun exposed defrost element defrost termination switch ok therminster didn’t check out the thermistor sends the signal to logic panel then run the the freezer ice machine and refer temps it took 24 hours before the system starting to show results freezer compartment 10 below ice compartment 0 degrees refer temp 37 degrees one refrigerant three different temps system is running at optimum performance 450.00 $ service call the thing with GE appliances there is no wiring diagram .thankyou parts select .ill use you on all domestic service calls.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

Replaced door circuit board. Vert simple to do. Problem was not solved! Replaced the main board with advice of ge tech. problem not solved. Currently waiting for the Tech to reappear. Not a happy person

Snap filter into place while holding the filter slightly away from the refrig. When filter snaps into place, push it towards refrig into place.

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.