GY398LXPQ03 Whirlpool Range - Instructions

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare

Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

R&r

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

First, I turned the circuit breaker off to the range. Then, I pulled the range out so that I could get to the screws which held the glass top in place. They were located on the sides of the range. I had to remove the trim pieces on the sides to get to the forward screws. Once that was done, I lifted the glass top, unplugged the wire harness, flpped it over on a protected surface. I noted the numbers on the old coil where the clips held it in place and put the clips on the new coil in the same place. The old wires just clipped on to the new coil exactly as they clipped on to the old coil. I put it all back together and it works great! I am a 70 year old woman who did this all by myself. You young guys should have no problem.

We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.

I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.

Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm glad I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.

screwed in the new oven light

Ordered part needed. Much, much cheaper than purching a new range.

This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.

I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?

Followed the easy instruction sheet provided.

Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.