GTDP280GD4WW General Electric Dryer - Instructions

Replaced the knob

removed old broken knob just pulled it off,replaced with new one took about five seconds.

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.

If your dryer is making a grinding or loud plastic rubbing noise, you likely need to replace the slides. Here is how I did it.

TIP: Before beginning, set out a hand towel on the washing machine to set the screws onto, in the order and position you removed them.

IMPORTANT: Before beginning, turn off the gas to the unit and unplug it! This repair is all done from the front side of the machine, so you should only need to slide it out enough to unplug it.

Step 1: Remove the control panel

To do this, you need to pull out on the round silver control knob to remove it. This will expose a long screw. With the long screw removed, grab the panel with both hands and slide it straight up. Be careful, the control board is still connected with a 40-pin ribbon cable. Set the control board on top of the dryer temporarily.

Step 2: Remove the lid

There are three screws to remove the lid. Remove them and set them on the screw holding towel. The lid is attached at the back, so to remove it you need to slide it forward towards the front of the unit. Once the lid is loose, you can have a helper hold the control panel while you set the lid aside, or gently let the control panel dangle.

Step 3: Disconnect the control panel and wiring harnesses

Gently pull on the 40-pin ribbon connector until the control panel ribbon cable is removed. There is a notch to designate which direction the ribbon cable it goes back in. Set the control panel to the side. At the same time, you can disconnect the two wiring harnesses that feed the door light and sensor. These wiring harnesses are secured to a silver plate with a zip tie. Cut the zip tie with your diagonal cutters. (You can trim the old zip tie and replace it by feeding the extra small zip tie through the original opening later.)

Step 4: Remove the steel plate that the wiring harnesses were attached to

There are 6 screws to remove the steel plate. Pay attention to where the extra large head screws go, because these are what the control panel slides onto, when you put things back together. Pull out on each side to release the bottom clips, then slide it upwards. Set this piece aside.

Step 4: Remove the front panel (the door panel)

There are 4 screws to loosen the door panel. Two silver screws at the top, and 2 white screws at the bottom. Loosen the white screws about half way. These do not need to be completely removed because the door can rest on them. Remove the top silver screws. Gently lift the dryer drum off the front bezel while you tilt the front panel towards you. At this point you should be able to see the white and dark green slides. I found it easier to lift the front door off the white screws and set it up against the wall.

Step 5: Replace the slides

The slides have plastic hooks that go through the round holes on one end to hold them in place. You should be able to remove the slides with your fingers (maybe with a little help from a flat-head screwdriver), and replace them. There are dozens of YouTube videos on how to do this if you need help. Be careful not to break the plastic hooks that hold the slide to the front plastic bezel. Replace white slides with the white, and the dark green slides with dark green.

Step 6: Putting it all back together

Do everything in reverse. Set the front panel in the white screws, lift the drum, and slide the door panel back to rest on the slides while you put back the silver screws. Give the drum a few good spins manually to make sure there isn't anything still rubbing. Keep in mind the sliding noise is slightly louder than normal until all the panels are replaced.

It will help the process to only tighten the screws half way while putting them all back in. Once everything aligns, then you can tighten them down. DO NOT over tighten, use hand tightness only or you will strip them out. With the front door panel back on, you can put the steel panel back in place. Once you have the 6 screws done, remember to slide a small zip tie through the previous hole to secure the wiring harnesses. Connect the harnesses, and the front panel ribbon cable before putting the lid back on. Insert the screws to the lid, then slide the control panel back down, and replace the single long screw. Note that the control knob is notched, so align the flat sides as you put it back in.

Plug it back in, and turn back on the gas, you are done!

UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.

The video on the site is easy to understand and a snap to follow.

remove the broken one and replace it with the new one

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

Replaced High limit thermostat per video on the website. However, the flange of new thermostat is flat, while chassis it mounts on is round to conform to drum of dryer. So new thermostat was not flush with chassis. Dryer did not shut off early (that problem solved), but instead continued to dry clothes beyond time necessary. Note that old thermostat had one side of flange slightly bent and probably more flush with chassis, and better able to sense when hot temperatures were reached. I dismantled dryer again, slightly bent new flange, re-installed. Seems to work better now .

inserted the lint catcher into the opening to replace the old one

Removed 3 screws that hold on front plate. Snapped out timer and replaced with new one. Attached one wire at a time from old timer to new timer. Reattached front panel and put on new knob. You can also watch on utube.

This was so easy. I used needle nose pliers to reach in and remove the metal clip which had slipped off of the inside of the knob and was on the post the knob was supposed to attach to. Next, I lined up the flat side of the "D" of the inside of the knob to the flat side of the "D" on the post and pushed it in until it snapped into place, and I was done. The dryer now works like new.

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.

All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.

easy to fix took less than 10 minutes

I bought all three parts but I noticed that the dial was very loose. I reapaired this first and it was working