GSS23GSKKCSS General Electric Refrigerator - Instructions

1) Unplug Refrigerator. Remove all shelves and light shield in the freezer.
2)Remove panel covering refrigeration coils inside freezer in back. Two hex head screws w/nut driver.
3)Remove the defrost heater using phillips screw driver. Two screws.
4)Unplug two quick disconnect stakons and wires from heater.
5)Plug the wire coming down the right side into one side of the new heater and plug the shipped white wire into the other quick disconnect spade at the heater.
6)Install the new dual element defrost heater into the same place where the old was. Connections to the right.
7)Route the wire that was on the left across the top of the coils and down the right side.
8)Bring the existing wire from the left side down the right side and the white wire up the right side. Wires should not be tight at all and do not remove the tape at the stakon.
9)Now wires need to be cut (if necessary)and crimped together in the shipped stakon. This stakon looks like a wire nut.
10)Wires should be tucked gently into the styrofoam up and down the right side. Wirenut should be positioned so that water can not collect in it.
11)Replace the panel over the cooling coils.
12)Plug Refigerator back into the wall outlet. Put shelves and light shield back in.
13)My refrigerator is now working without a problem. It's been est two weeks.
Ice maker is also working correctly.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

I removed the old shelf and installed the new one!

The new shelf went in really easy. It just fit in the alloted slot.

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

Emptied the door bin, removed it from its slots, and gently spread the plastic bin sides allowing the broken face panel to fall out. Replaced one end in the notches, gently widened the opening at the other end to slide the new face panel in, and jiggled just a little to seat the panel fully. Done!

Repairs on purchase of the parts were easy and went great

Watched a parts.com video on how to change defrost thermostat and followed the instructions

Had to remove a couple of shelves, then used a Phillips screwdriver to remove the Light diffuser then removed the "light board" assembly and unplugged the light board, plugged in the replacement board, snapped the board back onto its mounting bracket, then snapped the bracket back into its place and then replaced the light diffuser and screwed it back in place. Replaced the 3 shelves and the food which I stored in our chest freezer while I did this repair. I'M DONE !!!! Pretty easy. The switch was OK. Didn't need replaced. Then I plugged in the refrigerator. NOW when we open the freezer door; LET THERE BE LIGHT !!!!!! Sunglasses are needed now!!!

Despite attempts to quiet the 2 year old fan, I went ahead and replaced it. Part Select was prompt with a new one at my door less than 24 hours. It was just the fan motor, so took a couple extra steps to place it in the metal housing, but no problems and though the frig still makes noises, it's not coming from the fan as before.

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

Using Allen wrench removed broken handle. Using same Allen wrench replaced new door handle.

Removed tension spring, removed old lever, installed spring on lever, inserted lever in hole, re-attached spring to hook under front of refrigerator.

Followed the instructions on the repair video and it made very easy. Also saved us a lot of money. Thanks for your help.