GSS23GSKGCSS General Electric Refrigerator - Instructions

The trouble shooting information on the web site indicated that the damper door within the climate control unit may be broken. This was easily confirmed and the replacement of the climate control unit immediately returned the food locker temperatures to the digital electronic thermostat settings. The part has an improved ventilation gasket interface between the food locker and freezer. The unit works perfectly again, and the food locker temperature is exactly what the thermostat setting is.

Slip out old one, slide in new tray!

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

Before replacing the top filter housing, ensure the inlet water valve is operational. Replacing is a straight forward process. Unhook the houses from the inlet water valve in the back of the refrigerator. Remove and replace the top filter housing and ensure you replace the sealant using plumbers putty or sealant dicor butyl putty.

1) Unplug Refrigerator. Remove all shelves and light shield in the freezer.
2)Remove panel covering refrigeration coils inside freezer in back. Two hex head screws w/nut driver.
3)Remove the defrost heater using phillips screw driver. Two screws.
4)Unplug two quick disconnect stakons and wires from heater.
5)Plug the wire coming down the right side into one side of the new heater and plug the shipped white wire into the other quick disconnect spade at the heater.
6)Install the new dual element defrost heater into the same place where the old was. Connections to the right.
7)Route the wire that was on the left across the top of the coils and down the right side.
8)Bring the existing wire from the left side down the right side and the white wire up the right side. Wires should not be tight at all and do not remove the tape at the stakon.
9)Now wires need to be cut (if necessary)and crimped together in the shipped stakon. This stakon looks like a wire nut.
10)Wires should be tucked gently into the styrofoam up and down the right side. Wirenut should be positioned so that water can not collect in it.
11)Replace the panel over the cooling coils.
12)Plug Refigerator back into the wall outlet. Put shelves and light shield back in.
13)My refrigerator is now working without a problem. It's been est two weeks.
Ice maker is also working correctly.

I removed the old shelf and installed the new one!

The new shelf went in really easy. It just fit in the alloted slot.

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

replaced with new connector and it worked great. also replaced the water filter and that was super easy!

1. Slide out refrigerator away from wall.
2. Unplug refrigerator electrical cord.
3. Slide out refrigerator further to be able to get in back of.
4.Turn off water control going to refrigerator.
5. Clear top shelf around water filter area, remove water filter.
6. Remove water filter cover housing lid by lifting off.
7. Using a ¼" nut driver, remove two screws attaching water filter housing.
8. Go to back side of refrigerator, & remove 2 screws from the silver cover plate of MWD manifold water line unit.
9.Using ¼" nut driver, remove lower cardboard cover that protects the motor & fan area.
10. Clean motor & fan area with old tooth brush gently, & vacuum dust off.
11.Using (2) ½" open end wrenches, loosen & remove both water lines.
12. Go to front inside of refrigerator. Gently pull out old water line manifold assembly, you may have to twist it some to get the protective sleeve out of the hole.
13.Insert new water line manifold assembly into the hole, when it gets to mostly in, gently work the protective sleeve through the hole.
14.Position the new manifold water filter housing into place & reinstall 2 screws. Do not over tighten.
15. Go to back side of refrigerator, gently push down on protective sleeve so you then can replace silver cover with 2 screws. Do not over tighten.
16. Remove old tape that was originally holding water line tubings.
17.Connect water lines to water supply lines, using (2) ½ " wrenches. Tight, but not over tight.
18. Re tape water lines to back of refrigerator, using a strong tape like duct tape in an orderly fashion.
19. Turn on water supply, check for leaks.
20.Re install black cardboard piece on lower end of refrigerator.
21. Plug in refrigerator.
22. Install water filter inside of refrigerator. Install cover over filter housing.

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

Emptied the door bin, removed it from its slots, and gently spread the plastic bin sides allowing the broken face panel to fall out. Replaced one end in the notches, gently widened the opening at the other end to slide the new face panel in, and jiggled just a little to seat the panel fully. Done!

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.