GSG22KBPDFBB General Electric Refrigerator - Instructions

All I had to do was open the box, pull the drawer out, insert it in the fridge, and place the handle on and I was done. Thank you for making my fridge look new again!!

Took 2 seconds to replace door

Ordered replacement

Slid new drawer in.

ordered a new one; took 1 second to put in.

I started out replacing a bad thermostat, no problem,
when I hooked up the water, I found that the water resovior had a leak.
I replaced the resovior, easy fix, but I had to buy two 5/16 brass couplers.
then I found that the box would not get below 10 degrees, and the suction pressure was very low.
I figured that the fan motor was burned out, so I opened up the access covers, the fan motor was hanging there with broken mounts, so I replaced the motor, and repaired the mount.
Everything works great now, The parts shiping was very fast, I was impressed.
I thought I was going to get away without fixing everyones
HVAC problems when I retired.
Friends and family still remember that you are the HVAC man.
Tom

Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.

GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.

I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.

So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.

So now I'm back to order the ice maker part. The door flap will wait for another time.

Note: I've put in the time for novices and recognizing how the freezer is constructed.

Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.

Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!

You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Snap out old dairy door, snap in new one in about a minute. Slide out old vegetable drawer, slide in new one using care to pass the door lock without breaking the drawer slide on right side, about two minutes.

aligned and pushed on by hand

Replaced Temperature Sensor and now it is getting cold.

I removed the top vent and unplugged the ice machine ,took the back cover off the freezer.Removed the old fan which was pretty easy(unplugged it after I took the housing out for easy access) I plugged the new fan in and put everything back in the order I took off, and yada yada yada we have cooling.

This was generally an easy fix. The work was in such a confined area of our side by side and my husbands shoulders are broad so that was a little more challenging but overall a quick, easy and cheap repair doing it ourselves without having to call a appliance repairman.

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks