GSD4100J00CC General Electric Dishwasher - Instructions

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.

Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

I removed 2 screws a wire plug connector and replaced the old part. The total repair including putting the cover plate back on only took about 15 minutes. Also I saved approximately $130.00 by doing this repair my self.

Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

Simply opened the dishwasher door, removed the gasket insert located in the middle inside of the door and replaced with new. Also went ahead and replaced the seal on the inner edge of the inside dishwasher door. Found very simple instructions on Google on how to do make this repair. Very easy!

Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.

First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.

At first I thought I would call a repair man.Then I thought-that will be at least $100!So we went online and found the part.Took about four days to arrive.I pulled the dishwasher out and turned it on it's front.The little leaking hose was easy to remove,two clamps,and the new one installed.Total cost-$14.00.

from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.

Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.

The replacement of the motor and pump assembly went smoothly and without difficulty however this did not fix the problem. It then appeared that the inlet water valve was not operating properly, so this part was ordered and instlled, a very simple proceedure that could be done witrhout removving fthe dishwasher from its cabinet. -- Again failure to run -- the timer assembly and electronic panel were then removed and examined. The control panel had no visible defects, so the timer assemblyand its cover was removed and examined . Uing a variable power supply the drive motor for the timer was energized and tested. As the motor ran properly the electrical switching contacts were then carfully checked, it was discovered that one contact set was heavily pitted and burned. These contacts were carefully cleaned and pollished with 1000 grit sanding paper. The actuator leaves were examined and two sets were found to be slightly out of alignment. The leaves on these sets were bent slightly to insure they were in line with the rest of the leaf serts. It was then noted that the rotating leaf('s) actuator had a home position indicated by a molded depression at one location and the motor was energized using approximately 5 volts ( a nine volt battery could also be used as a poer supply) observing prolper polarity to run the rotator until the home position was established and the actuator rods paul dropped into this depression. The assembly was then replaced in the diswasher using care to make sure that the actuation arm and spring were positioned properly weith the arrow end of the arm located in the recesss of of the rotating timer disk use care in placing the assembly and do not lose the sping which attaches to a mounting post and the arm. You may want to take a picture of the spring and arm locations when you rwmove the timer assembly to properly re-assemble all components, the repaired unit was placed back in its cabinet and a full cycle run to establish proper operation. And unit checked ok! Some of these proceedures are not for the weak of heart. I am a retired engineer who has been repairing my own equipment since graduation. .

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.