GSD2001G02WW General Electric Dishwasher - Instructions

Used drill and easy out to remove broken part, then put in new one

I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.

Opened package, removed cap and screwed it in place.

Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.

Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)

Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.

Unscrewed unit from counter and loosened legs using adjustable supports under dishwasher. After switching off water under sink and power at circuit breaker, removed motor and pump assembly and replaced with repair kit.

Turned off the electricity to the dishwasher,removed the old solenoid,and put the new one on(very easy),turned the electrical breaker back on.

After removing the front panels, I removed two screws holding the valve in place. I turned off the water supply and removed the water line, unclipped the hose clamps and took the faulty valve out. I then reversed the above steps and turned the water back on. NO leak. Very easy to do andthe repair took ~20 minutes to complete.

Recieved universal parts f/ pump & mtr assy. sorted them out, picked the ones I needed to complete my repair. Installed new assy, checked operation and was completly done in about an hour.

My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!

I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.