GSC8630SW119 General Electric Dishwasher - Instructions

first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Simply screwed in new cap

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Went to repair parts on troubleshooting and found check valve assembly to be most common problem. Went to parts diagram to locate assembly and found it somewhat confusing as to exact location. Ordered part(s) on percentage as the problem. Received part next day (great)! Pulled dishwasher out and found I did NOT need to do so to replace check valve which is replaced without having to remove dishwasher. The gasket replacement was not necessary as it seals sump area from bottom of dishwasher and not the valve as it appears on the parts diagram. It took about 2 minutes to replace valve itself and it was the cause of the problem.

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.

Each replacement wheel came in two parts: the wheel itself and the clip which had to be pushed through the center hole in the wheel in order to attach each wheel to the carriage that holds dishes. I had difficulty assembling the clips and wheels until I ran the clips under hot water to soften them. This made it possible to assemble the wheels and attach them to the dish carriage. I would have preferred the wheels to have come assembled, particularly given the price of each one.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

Put on a new cap.

Pulled washer out about 6" without disconnecting any hoses. This way i could use both hands from the left side & front after i took the kick plate off.

Determined not to call a repairman for such a simple problem, I watched your extremely helpful video. The ordered parts came right away and all it took was a screw driver and 30 minutes to take off and replace four rollers. So easy, this 75 year-old grandma could do it!

Pop the end caps off the slides by pushing the lock tab in with a medium flat screwdriver, through the square hole in the side of the slide. Pull the rack out and set it on the counter. Pop the axles off, with the rollers, with your fingers. They are just clipped on to the rack wire. Pop the new ones on 4 places, fingers only needed to clip them to the wire. Put the rack back in the dishwasher by aligning the rollers in the metal slides and pushing it in like normal. Pop the rack slide end caps in by just pushing them in. If you're smart you bought new ones, they're cheap insurance. Save any good used parts in your kitchen junk drawer for the next time you treat it rough. Less than 5 minutes to fix. So easy a caveman could do it. One just did!

Snapped right in