GS475LEMS2 Whirlpool Range - Instructions

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

The repair was VERY simple....2 screws, remove the broken handle, put now one in place, put back the 2 screws... done!! What I want other to know... is who with about 6 clicks from my home pc, I had the exact part i needed, ordered!!! I was dreading ordering this part so much because of all the hassle I have in getting to a website to order, and all the crap that goes with finding, the part....the ordering the part. This site was SOOOOO cool!! The handle had been broke for almost a year, and didn't want to replace it because of the usual hassle that goes with 'The Hunt". If I had know that Parts Select was so good about this, I would have had the new one installed 3 days after the original handle broke!! And shipping was SO FAST!! Have you people in my book marks for sure!! Thank you one and all!!!

oven would not light but broiler and range top would. removed oven racks. removed 2 finger tight screws on oven pan floor and pulled up oven floor. also removed storage drawer under oven- also 2 screws. now your oven should look like the inside of your gas grill. removed 2 more screws on burner plate and removed plate. unplugged igniter and 2 screws holding igniter. replaced igniter and put together in reverse order. oven now works perfectly

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.

The first thing you need to do is remove the racks from your oven.

Then look around at the back of your oven for the screws that hold the bottom pan down.

Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.

Remove the heat shield that is over the burner.

Remove the bottom drawer of your oven.

Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.

Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.

The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.

Once you have the old igniter out then you can carefully install the new one.

Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.

Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

Took off the old handle ,cleaned the surface then peeled off the double sided tape and replaced the new handle.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.