All Installation Instructions for Gibson Refrigerator GRS22PRBD0

end piece broken that held bar on freezer door shelf

attached the bar to the end piece and slipped it into the proper opening. Easy I ordered the piece one morning and received it the next morning. Great service.

Parts Used:

Door Shelf End Cap - Left or Right Side

Betty from Seal Beach, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

first fresh food too hot, then freezer too hot

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

Parts Used:

Defrost Timer - 60Hz 120V

Rita from Lake Luzerne, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

the freezer would stick in defrost and not come out

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

Parts Used:

Defrost Timer - 60Hz 120V

carol from woodland, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

storage drawer frame had cracked in the back

Simple, removed old frame, took off the humidity slide control and installed on new frame. Slid it back in place. Great service, had it the next day, thanks.

Parts Used:

Crisper Drawer Frame

David from WETUMKA, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

drawer and rails broke due to under design of the components

This was the second time i replaced the drawer and the first time for the frame.The repair was simply removing the old frame from the refrig and removing the rollers from the frame with screw driver. The rollers are reused with the new frame.The frame was reinstalled in the refrig.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.

Parts Used:

Lower Crisper Drawer

Crisper Drawer Frame

Bruce from State College, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The original support was broken, tried epoxy and it only held for a few months before breaking again

All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.

Parts Used:

Crisper Drawer Cover Support

Arand from Yorktown, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

door brackets were broke off refridgerator

Put the end caps on the metal bar and put it on the freezer door and it snapped right in.

Very easy to do in less then 4 minutes to do both shelves.

Thank you very much.

Parts Used:

Door Shelf End Cap - Left or Right Side

Tonda from Holland, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Defrost timer was not working

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Parts Used:

Defrost Timer - 60Hz 120V

Harold from Grants, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Slide ridges were cracked and broken

I used a small screwdriver to pry the tabs of the front glass panel loose, and then slid it upward and out of the broken storage drawer. Then I slid the panel into the front slots of the new drawer and pushed in an evenly downward manner until it snapped in place. It was an easy task and now we have a new drawer that slides smoothly.

Parts Used:

Upper Crisper Drawer - Front NOT Included

John from Watertown, WI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Right side door was grinding on the spindal.

We took the door off and replaced the pastic washer. Found out that the repair people never informed us that the door itself has a bit damaged so this repair would have to be done over and over. Nice way for them to make money off us.
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!

Parts Used:

Door Hinge Washer

Donna from Palmdale, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

The supports for the crisper cover had broken and the draws would not open correctly

I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.

Parts Used:

Crisper Drawer Cover Support

WAYNE from NOVATO, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Shelve pan broke on side

Removed old pan and cleaned all surfaces and reinstalled new pan.

Parts Used:

Upper Crisper Drawer - Front NOT Included

Edwin from ROADBURNS, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Light wouldn't turn on when door opened

Unplugged fridge, opened the door, used flat head screwdriver to pop off old switch, unplugged wires, plugged in new switch, popped it back in, and plugged the fridge back in. 2 minute fix.

Parts Used:

Light Switch

Matthew from SOUTH BEND, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Temperature in both freezer and fridge sections to warm!

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work

Tom Houck
Spokane, WA
Houck Photo
509-723-3418
[email protected]

Parts Used:

Defrost Thermostat

Defrost Timer - 60Hz 120V

Thomas from Spokane, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Fridge quit working.

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Parts Used: