GRML3500SW-2 General Electric Range - Instructions

frances from winston salem, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner bowls had been used and abused for year gone by in this rental.

Replaced them all. Next I want to replace the burners.

Parts Used:

Diane from Rio Rancho, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

6" and 8" burner bowl replacement

Slide out burner elements. Remove old burner bowls. Insert new burner bowls and reinstall burner elements.

Parts Used:

Shawn from Lubbock, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

handles broken on oven door

removed old handles and slid door apart align new handles and re-installed new handles. One person job.

Parts Used:

Rita from Yadkinville, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

The burner bowls were encrusted with grease and spills.

I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.

Parts Used:

Ed from Canyon City, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Handle on oven door end cap cracked

The repair was easy except what caused it to break .Their was a missing screw on the door itself that was never put on or came off could not find old screw,once it was replaced new part was stronger than before.

Parts Used:

Garry from SAN ANTONIO, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

The original oven handle end caps were cracked

I disassembled parts and panels from the oven door as needed to remove the handle end caps. It was not clear to me what the best disassembly method was, because I used a different method when assessing the problem as when I performed the actual part replacement. The quickest way is to take the top two screws on the inside oven panel loose, but leave them in their retainers. Remove the side trim screws on the plastic upper side pieces. Remove the four sheet metal screws on the bottom of the door, located the far right and left (two on each side). Carefully split the inner and outer oven panels to access the mounting screws for the oven handle. Replace the oven handle and reverse the disassembly process.

Parts Used:

Chris from New Ulm, MN
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Replaced All Burner Receptacles After One Failed And Also Replaced Ball Burner Bowls

This installation was for a replacement for one of the burner bowls on the original order. Replacement bowl fits proiperly.

Parts Used:

ROBERT from MECHANICSBURG, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Broken handle end cap

I removed the two screws in the oven door with a T-15 screwdriver and pulled the inside frame away from the front glass. At which time I hear something came loose it was the oven door spacers, got back on the web site to see were they went from the parts list and put it back together in no time.

Parts Used:

Thomas from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Left oven door bracket broken

You need to remove both ends first you block up under the oven door so it is flat to work on then, you will see inside the door the to sleeves that the long screw goes through is easier to screw back in,you are on the road to finished product. H.l.R

Parts Used: