GLWN5050M1WS General Electric Washer - Instructions

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.

Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.

I removed the bottom pan and found the problem , It was the drain hose , then I removed the hose , and began to look for a replacement part , and my search lead me to Parts Select .com , It was MOST helpfull and for that I thank you guys , I got my part and insalled it in about 15 min. and took the machine back into the laundry room hooked it up and it's been doin good sense .

Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.

I googled "water not draining washer" and found a video made by Partselect.com on youtube on how to replace the water pump for a washer. So, I went to their website and punched in the model number of the washer and found the water pump I needed in stock. It said it takes an average of 1.8 days for delivery. I ordered it on a Sunday and by Tuesday I had the part delivered to my front door. That night after work, I went down to the washer which I already had sitting face down on the floor with the back peeled off and the pump out from the weekend so I could compare how it looked with the online pictures. The new part came already mounted on a new bracket so it was just a matter of installing the bracket and hooking up the intake and output hoses. In order to make my job easier in the tight space, I removed the drain hose from the bottom of the wash basin by squeezing the pressure clamp with a large pair of adjustable pliers. I then installed the other end of the drain hose to the pump itself. I then hooked out the end of the output hose to the other part of the pump that pumps out the water to the sink. I first removed the clamp on the back of the washer that held the output hose to the back of the washer. That gave me more leverage to move the pump around for the installation. Once both hoses were clamped onto the pump, I used a ratchet socket wrench to install the two bracket bolts directly onto the base of the inside of the washer in the same holes using the same bolts as the old pump. Once that was tightly installed, I Hooked the other ends of the two hoses to the bottom of the wash basin and to the back of the washer respectively. FInally, I connected the ends of the two wires into the clips on the pump in the same order as the original pump. One white one black. Finally I screwed in all the short sheet metal screws that held the back washing machine cover on. It was about 12 screws. I then installed the drain hose with the original bracket to the back of the washer. Satisfied that everything was installed tightly, I stood the washer up and then hooked the water hoses back up to the faucets and tightened them snugly with the large adjustable wrench to ensure it did not leak. I plugged the washer back in, hooked the drain hose to the sink and then filled the basin up partially. Moved the control to the drain mode, and the water came out wonderfully. Note, when the pump was broken, I was able to drain most of the water from the wash basin by lowering the drain hose the a bucket on the floor and letting gravity do the work of draining it. I had to fill the bucket several times and dump it into the sink, before I was able to drain all the water out and then lay the washer face down on the floor to remove the back of the washer. Thanks for the part and quick delivery. I saved a lot of money on repairs by doing it myself.

replaces as per video. Very helpful

Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use

Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

followed video

I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.

The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.

I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!