Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a door striker, it is gray in color and is a part found on your washer. The purpose of the striker is to keep your washer door closed for usage. This piece will attach to your appliance lid an...
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. T...
This washer drain pump assembly is designed to efficiently remove water from front-loading washing machines during the drain cycle. It plays a critical role in maintaining proper water flow and cycle ...
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
This is a single spring with insulator, but you may also know it as a suspension spring. It is a part for your washing machine. If your tub is no longer stable, which would cause shaking, moving, and ...
This drain hose is designed for use in your washer. The function of this part is to carry water from the drain pump to the house drain. If your washer is leaking or will not drain, you may need to rep...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are...
Is your Toro equipment not operating as smoothly as it used to? Sounds like you might need a new upper handle. Let us help you get back to peak performance with our Authentic Toro Upper Handle. This i...
Ask our experts a question about this model and we'll get back to you as soon as possible!
10 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wendy
February 16, 2020
In spin cycle I hear a clunking sound and it seems out if balance with any load.
For model number GLTF1670AS0
Hello Wendy, Thank you for the question. Normally this indicated the Bearing is worn. The bearing is only sold as part of the Rear Outer Tub Assembly, so the Rear Tub will need to be replaced. We hope this helps
Hi,
During the spin cycle on our Frigidaire GLTF1670AS0 front loading wash machine the sound has gone from a “high pitch jet engine sound” to a much LOUDER “jet engine sound” with a higher pitch.
Thanks,
John
For model number GLTF1670AS0
Hello John, thank you for getting in touch. Based on our research, we would recommend checking the following parts to fix your issue: drive belt, part number PS419285, drive pulley, part number PS419285, and drive motor, part number PS1990829. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
The rinse cycle begins normally with the drain pump discharging water, but then remains stuck in drain mode and does not advance to spin. What should I check next?
For model number GLTF1670AS0
Hello Kevin, thank you for getting in touch. Your washer may be facing this issue because of the faulty timer. The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences. We recommend you replace the timer, part number PS419227, to fix the issue. We hope this solves your problem!
SERIAL # XC31612262 (115vac-60hz-12AMPS) I REQUIR THE TOP FOR THE WAHSING MACHINE AS IT WAS A STAKING UNIT AND NOW WE HAVE THE WASHING AND THE DRYER SIDE BY SIDE.
For model number GLTF1670AS0
Hi Sam, thank you for reaching out. The top panel for your model is part number PS419347. We hope this is what you were looking for!
THE DOOR DOES NOT LOCK AND THEREFORE WASHER WILL NOT START
For model number GLTF1670AS0
Hi Dean, thank you for the question. We would recommend checking the door lock assembly, part number PS12364048. It locks the washer door to prevent the door from opening during the wash cycle and the spin cycle. You may need to replace it to fix the issue. We hope this sorts out your problem!
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could sa
... Read morey that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.
