GLGQ642AS1 Frigidaire Dryer - Instructions

Removed old guides ( some of the snap in fastners were broken off). REplaced guides by rolling drum, easy to snap in @ drum bottom each time.

I determined the problem was the fan wheel and housing. I located the part on partsselect.com, Ordered it and installed the afternoon I got it in the mail. Perfect fit.

I have used partsselect before, always had great luck, great prices, always have the exact part.

First, I shut off the gas & unplugged the dryer. Then I disconnected the vent pipe so I could pull it away from the wall to access the back. Disassembling the dryer was simple.
there are 8 screws: 2 for rear access panel, 2 for top, & 4 for front panel! Once front panel is off, lift back of drum up 2 inches, then forward to get rear bearing out of it's bracket. My rear bearing had worn down so much it was 1/2 the size of the new one! It wore through the bracket down to the metal! I replaced the rear bearing & bracket assembly, as well as the belt & the spring for the belt tensioner! make sure you generously lubricate the new bearing as well as the tensioner pulley! The most time consuming part of this job was cleaning all the lint out the dryer cabinet& cleaning the drum. It works great now! I hope to get a few more years out of it!

Disconect power, Removed top and front of dryer.
The broken zipper was easly removed at this point. The plastic glides easly snap out and in. The felt took some more time to scrape off and clean the old glue. Glue the new felt into place and replace front and top. The parts were shiped promptly and the dryer was out of service for only three days.

lifted the top panel, there were 2 screws to remove the front panel, then the coils were right there on the bottom left side. a screw or two hold the coils inplace. Then just unplug the old coils and plug in to the new coils.

Ordered the new knob and stuck it on. Doesn't get easier than that!

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

used a putty knife to press the clips away from the door and lift the assembly away out of the door. Used the putty knife to push the clip over the lip and snap the new handle into place

All I did was push the new part into the machine! So easy!

This was a Sears Dryer, also know as Kenmore, This dryer can be stacked or side by side. In this case it was stacked. There are no directions on how to replace this part. For this model made in 2005 the lid of the dryer is held in front by two clips. You open the lid simply by prying the two front corners up with a flat head screw driver. The front of the top lid pops right up. You may have to remove the mounts in back if you cant lift the dryer lid enough to be able to get your hands in. UNPLUG THE DRYER I got a nasty shock. There are two wires on the switch, remember how they go and where they are, that's important. Turn the switch (from the front or back) so that it pops out. Remove and replace the wires put it back in (from behind/top) and twist a 1/4 turn into place. Plug, test and simply push the cover back down onto the clips. Done.

The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.

Simply put on the new knob. It took 2 seconds. Easy!!! So glad I didn't have to spend a small fortune for a repair. Thank you!

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

I basically followed the video instructions on your website. Pretty simple but ran into an issue pre-threading the 3 self taping screws into the spindle bearing. The screws provided were blunt on the end and did not tap easily at all. I used the existing screws that were much more "sharp" and worked much better. Also, the new screws were Philips drive and due to the amount of torque trying to self tap nearly stripped them out. The old sharper screws were square drive which had a better bite. So basically, I used the old screws to self tap and then used the new screws for the final installation.
It took a long time to clean all the lint out from the inside of the dryer. The motor was completely embedded with lint and animal hair. You may want to suggest that a good cleaning may be needed so bring a shop vac...and also something to carefully pick the lint balls out from around the motor armature and bearing area. Overall the video instructions were really a big help!

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.