GLD5950NC General Electric Dishwasher - Instructions

Repair is super easy and anyone can do it in no time!
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.

2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!

This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.

The repairman offered to fix the dishwasher at a cost of about $200 or supply the water inlet valve for $85. Google led me to PartSelect.com where I easily found the correct part for $45. I received the part in 2 days by FedEx ground.
The hardest part of the repair was removing the dishwasher from the cabinet. I took the dishwasher out a short distance to the patio where I replaced the water valve...about 10 minutes.
I then made a makeshift connection to an outdoor water hose and connected the electricity and ran the dishwasher while out on the patio through a short cycle to make sure of the repair and check for leaks.
Then reinstalled into the cabinet...total time about 2 hours.
Thank you PartSelect.com

Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.

unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

Removed the lower rack and installed new wheels with clips

As per instructions, any one that can read and use basic hand tools could do it. Very nice color instructions. BTW, this was an excellent value, $20 cheaper than two of the other parts houses I checked. Super fast shipping

Bought a new lower rack with wheels. Take out old rack,remove new rack from box. Check new rack and find two wheels missing from rack and nowhere to be found. Check old rack and find the best two wheels,remove from old rack and place on the new rack. Slide mostly new rack into washer and save a few more old wheels—just in case. Notify company and get no response until today!!!

The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.

The repair was very easy and straight forward. I removed the electrical wires, removed the two hose's and then removed the old valve from the dishwasher frame. To install the new valve, I just did everything in reverse. No problem and I saved about $80 for the repairman to come out and I am sure I would have paid more for the valve if he provided it.

Thank you.

very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.

Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!

took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down

Called repairman: announced that the drain pump was gone. Did not seem right. Went to the website. Found what I was looking for. 49% of the time it was a check-valve issue; only 26% of the time was the pump the problem. Took the unit from under the counter; got it on its side; removed the drain pump. Found my first check-valve, but thediagram showed a second lower one toward the sump. Having located both and purchased two valves and and the lower holder piece, I was ready to finish the job. Quarter-inch nut driver and a screw driver and the valves were in and the drain pump re-installed. Most difficult in my case was getting the dw back into its spot and lashed down! Thanks for the good guidance!