GLD4550V00CS General Electric Dishwasher - Instructions

Cut power and water flow to the appliance. Laid appliance on its side, removed the electrical lead from the motor. Remove the mount from the back of the motor and loosened the two clamps- one to the sump and one to the discharge tube. Removed and replaced the pump/motor assy. with the new one, reinstalled the clamps, rear mount and electrical lead. Righted the unit and fired it up. Worked fine.

Easily screwed on this part and used it for the door of the dishwasher to properly open and close

Open dishwasher. Remove the screws on plastic cover of door. To cover off back of plunger replaced with new one. Reinstalled screws in door and everything worked

simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.

look at neww part first then r&r

I carefully read over comments from other people's experience first. I removed all the screws from the inside panel and had several heavy books to weigh down the door. This allowed me to remove the white inside panel, turn it to get easy access to the seal at the bottom. All that was necessary was to clean the area of builted up soap etc, start pulling old seal off from one side and at the same time insert the new seal in same track and groove, being careful to have the new seal lined up in the same manner as the old. The whole process was rather simple and required very little effort.

pulled switches flicked leaver worked when itwanted to and not every time. I removed then shorted then rechecked everthing worked. got on line ordered parts good price fast service fixed 30 min when they came in saved money.Thank God! 20.00 fix instead of 200.00 +

Replaced pumped with new pump and now its not leaking and dishwasher is working great now.

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.

Shut off water, disconnect drain line from disposer. Remove dishwasher from wall and remove water feed line. Unplug or disconnect power to unit. Remove upper and lower dish racks as well as lower water sprayer bar, and filters. Lay dishwasher down on backside (make sure to catch water with bowl). Disconnect pump connector with nut driver and replace. Stand dishwasher back up and reverse removal process

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

Removed the screws holding the inner door panel from the door. I just flipped it over and used the weight of the removed panel to hold down the spring loaded door. I took note of the position of the old seal and then removed it. I cleaned away all of the accumulated soap residue. The new seal was positioned by just sliding it into place. I flipped the door panel over and replaced all of the attaching screws. Don't try to press the new seal into place. Slide it onto the lip of the door panel.

Just pop them in and you are done, less than a minute to install both lids.

I ordered it online and g0t it the next day. I found out why so fast. The parts select store was 3 miles from my house and I paid $7. 50 To have it delivered by fedex. I opened the box and set it in the dishwasher. I hope this helps someone. It did me.