GI15NFLTS3 Whirlpool Ice Maker - Instructions

Unplugged the refridgerator and pulled the rear cover. Had to take the fan blade off in order to get at the screws holding the existing motor in place. Removed the old fan. Pressing the new plastic fan onto the new motor shaft was a little more effort than expected, but I guess it won't come off. I have large hands so mounting the new unit was a little bit of a challenge getting the small screws started. Once the three screws were tightened all I had to do is plug the electrical connector in and replace the rear cover. I was happy that the existing electrical connector was the right one for the new motor too, and that I didn't have to use the provided wire harness. All in all the repair went pretty well.

The repair went just fine. Your instruction regarding using the wiring harness were clear. Most of all I am happy to not have to listen to a noisy motor all night.

Removed to old motor by removing screws and disconnecting power source and replaced with the new motor and plugged back in power source

Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.

I tried WD40, it worked for a day. Got a new part from PartSelect.com and was a good brand. Panasonic. Easy fix and works great. Saved a bundle. I priced a new fridge, no way, this was better. Thank you Partselect.

as told per compter

UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simply replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

I called the 800 number and the lady was great to work with and helped me thru all the order process and confirmed the numbers. She also told me she would try to get the order out that day which she did and I had the part two days later. When it arrived I went to the web site and reviewed the video and went to work and all went as the video said. Thanks for the help and if i need another part I will visit your site or call.