GI0FSAXVB07 Whirlpool Refrigerator - Instructions

Looked at the new part to determine what I would need to remove the old part. It was very easy to figure out. I removed the old end cap by taking out the screws. Once the screws were out I popped the side of the end cap off. There is a horizontal piece along the back wall that is connected to the end cap. On the left side of this piece of plastic there is a small tab that clicks into the back wall. On the right hand end cap there is a sliding lever which controls the air in the deli tray. This control is made of plastic and appears to be pretty fragile> By gently bending this lever I was able to remove the control lever and install it on the new end cap. In all it took me about 15 minutes to complete the entire job. Very easy.

I removed the right side endcap and rear thermostat piece behind the pull out drawer. It was fairly quick, 3 screws on the exterior of the end cap and one screw holding in the drawer thermostat. The worst part was getting the thermostat control that connects the drawer thermostat control to the rear thermostat. After playing with the control rod I was able to to snap it in successfully to the endcap with the proper rod connection. The rear thermostat goes in first, then the endcap. Quick and easy. For $23 it would have cost over $150 to call a repair guy ($120 call charge plus parts). Thanks.

Saw U tube instrctions how to install and it was easy

First found U Tube video of my exact refrigerator, ice maker remove and replace. Many available, all are helpful. Watch several times. Once part arrived the repair went very smoothly. Only had some difficulty attaching the ground wire, had to loosen the auger motor to attach the tiny screw. Not difficult, just took a bit of time to get the angle on the screw correct.

Let the ice in the freezer melt while installing P trap drain tube

Replaced water/ice maker inlet valve from video instructions from Just Answer. The inlet tube for the water dispenser would not cede in the valve and this created a leak problem from the water dispenser connection. Called repair tech and he could not get the line to cede correctly in the inlet valve. Am going to request a replacement part. This has been very frustrating!

you tube video was most helpful. after getting new part and disassembling old ice maker, you have to change out the wiring harness. Reinstall ice maker, don't worry about the timing of the unit as it will do this itself, may take 10 hours to produce ice, mine took about 2 hours to go through its' cycles and give me ice. It is running great

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

Replaced two original crisper drawers with 2 new drawers; replaced broken end cap which required the removal of a few bolts and screws. The replacement parts were identical matches--a huge relief. The interior of the fridge looks like new. This follows upon not being able to get the parts directly from the manufacturer.

Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!

Repair was simple and just as described by several others on this site! From finding the part, ordering, quick shipping and instructions, PartsSelect made this job a breeze to complete.

I unpacked the glass and slipped it into the shelf. Done.
What was more impressive was the delivery time. I ordered the glass at about 12:30pm one day and the glass was at my door by 9am the next morning. Even my husband was impressed with that.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)