GFSL2KEYALS General Electric Refrigerator - Instructions

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

Received new drawer, washed same, removed old drawer and transferred items to new drawer, THEN with out further ado reinstalled same!!! Wa La all finished.

My need for a part wasn't about an appliance repair, it was about making my GE frig work better for my particular needs. There is a lot of wasted space in the 2 door (French door?) model, at least for me anyway, and so when I discovered your company, online, just by googling, I jumped at the opportunity to buy an extra shelf to use the space more effectively. I was surprised. Package came quickly and installing it took a mere minute. I should have done this years ago! I am one happy camper. Excellent service, excellent quality shelf. Thank you everyone at PARTSELECT

Removed shelf from refrigerator, screwed on new shelf support, replaced shelf. Got a kiss from my wife for fixing her 'fridge.' Easy!

I lifted the dairy bin up and out. From the top, I inserted the right peg of the new dairy door in place, then gently pushed out on the left side of the bin and down on the left side of the door until the left peg of the door popped into place. Put the repaired dairy bin back at the top of the refrigerator door and pushed it down into place.

Removed shattered glass and inserted the new one into the shelf bracket.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks

Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job

Took the old filter out and put the new one in.
Easy Breezy!!

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!