GFSF6KKYCBB General Electric Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
needed to replace the filter
-
richard from asheboro, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
French spring broke.
-
Andrew from Bensalem, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
6 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken plastic shelf cover
-
Michele from Birmingham, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Filter needed replacing
-
W Craig from Diamondhead, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
crack by the middle of vegi drwaer
-
Carole from Sunrise, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
replace water filter
-
Richard from Waynesboro, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Change Filter
-
GREGORY from SACRAMENTO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Factory installed rail was overtightened and fractured the rail. Subsequent use resulted in rail failure.
Remove drawers and internal shelf supported by rail(no tools). Remove rail (phillips). Remove roller from existing rail. Intall roller on new rail. Install new rail (phillips). Replace shelf and drawers. Note: New roller (identified as a separate part) and screws are not included with rail.
Parts Used:
-
Jared from Sandy, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broke side button on cover that holds it in
Just put it in the holes on both sides only problem is the printing on cover is up side down
Parts Used:
-
Loren from Litchfield, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
We needed a new water filter.
We received the part just a few days after ordering, unscrewed the old filter by hand, and installed the new filter the same way.
Parts Used:
-
Dan from Surprise, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice and Water Filter needed replacement
It was easy and fast, like changing a light bulb. The directions were clear and easy to follow. Thank you.
Parts Used:
-
Irene from Tigard, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
did not need adapter
exactly as the instructions.......never did see anything about replacing the adapter...therefore i did not
Parts Used:
-
terry from fort worth, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Evaporator freeze up
-
Peter from Homer Glen, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Evaporator Fan Failure
Disconnect power to refrigerator, Removed all upper shelving, slid the draw assemblies out 12 inches to gain access to lower retaining screws using my power screwdriver. Removed three lower retaining screws and two screws that hold the center shelf rail. Then removed the cover assembly by pulling out and down from the bottom of the assembly until I could access the connectors for the fan at the upper left hand corner. After releasing the lock tabs for the electrical connectors I removed the assembly from the refrigerator cabinet. There was an excessive amount of ice/frost buildup due to the fan failing so I used a blow dryer set on low to thaw the ice from the evap coils and related wiring and sensors. Once thawed and free from ice, I reversed the procedure to install the new cover. The procedure would have only taken about 10 minutes if it were not for the ice buildup. I would recommend letting the frig thaw first if you have another place to store the food. Overall, very easy to install.
Parts Used:
-
Fran from Mount Vernon, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The plastic on the vegetable tray shelf was cracked
The repair was so easy. I had to take out all the food. Then I was able to easily lift the shelf out, and put the new shelf in and replace the vegetable drawers.
Parts Used:
-
Karen from Medford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!